JCBP24WL1WW General Electric Range - Instructions

The hinge mechanism in the back of the range top, could not be fitted to the new part. I needed to enlarge a couple of seat holes on the underside in the front portion of the new part to make it seat securely enough so the hinge mechanism could be safely deleted. (The new top is now simply sitting on the range, without hinge in the back).
More care should have been used to identify the correct top for the exact model and serial number of the range. Even though I had communicated those numbers when I ordered the part, and the picture looked like the correct part, the problem arose.

The broiler uses two male slip-on connectors that attach to two wires with female connectors in the stove. When removing the broiler element, I discovered that one of the two wires was burned in half specifically where the wire crimped to the female connector. This is abnormal and raised some concern. However, I deduced that the terminal crimp from the factory must have been defective and the wire nicked or cut in order to produce enough heat at that point for the wire to burn and fail. The female crimp terminal is a special, solid right angle design that I was unable to locate locally even at an electrical wholesale distributor. A straight terminal connector was used and crimped after stripping a new section of the wire. Heat will melt solder. You must use a high quality crimp connector and tool. The connector was then very carefully angled down slightly to maintain a safe distance from the back shield of the stove to the wire when in place. The new broiler works fine. There was likely nothing wrong with the old one. Just a wiring issue.

Followed the instructions online, very simple, quick and painless.

First I unpluged the unit from the recepticle, then unscrewed the back panal from the oven. I removed the to wire connections from the bake element and then removed the two screws from the element itself. I removed the element and did exactly the sae in reverse to install the new unit.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

First I unplugged the stove, then lifted the stovetop, then took off the top panel on the back and disconnected the two wires. Then unscrewed the terminal block and put the new one in its place. Lowered the top inserted the eye and replaced the back panel. Works great!

This is the second time in a few months that I replaced this terminal block, so I made sure the contacts were clean and smooth. I also made sure the contacts were completely inserted in the block.

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

After I ordered a new element unit, I read the "do it yourself" review on the page. I took the back off of the range and found the broken wire. I found that I had the same problem with the wiring, and that maybe the element was not the problem. I went to Lowe's and purchased a female spade connector, because no one would sell me one through the parts department. All I did was cut off the wire at the end of the burned section, stripped back about 1/2 inch of the wire and put on the new spade connector. I took off the origonal connector/crimp, and slipped on the new one. (You do have to make sure that the wiring doesn't touch the range back) The element was not the problem, so the origonal one still works fine. I may keep the element I ordered, just to have it if this one goes out. I didn't even need to remove the screws from the element inside the oven. It can all be done from the back of the range.

This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.

I just followed the instructions on the link provided with the part