GRCR3930TB-1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Georgianna from Austin, TX
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
End Cap broke on oven door.
It was easy as pie. Just followed the instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Glen Island, VA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace end caps
The video was very helpful.Very easey repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from De Soto, MO
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left bracket broken on range oven door handle.
Using a torx screwdriver, I removed the old handle bracket. I had to be careful not to lose a metal spacer that went between the back of the door front panel and the back of the inside door panel. With the door in full open position, I was able to hold this spacer in my thumb and fore finger while I removed the screw. The broken portion of the handle bracket fell to the floor. With the old handle removed, I placed the screw through a hole in the inside panel, through the spacer and through a hole in the front panel. While holding the front pull bar in the right handle bracket, I placed the new bracket on the bar holding it in position on the door and attaching the screw. Easy peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sandstone, MN
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Muskego, WI
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke end cap while moving range
unscrewed broken end cap, removed from handle and replaced the new end cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Kingston, NY
- Parts Used:
- WB7X7183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
left end cap for oven door
First, the order was shipped and delivered immediately. The model number had a wider range to select from and I had to guess which was the better fit. Other then that the new handle installation was a snap. Thank you and we would surely order from your company again.
Was this instruction helpful to you?
Thank you for voting!
Stove door handle broken
Unscrewed the old broken pieces to the handle and put on the new handle, very easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynda from Burdock, SD
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Small burner not working, outside was fine
Followed directions that I found on the internet and it was easy to remove the old burner and replace it with the one I ordered from you. There was no problems at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Baker from Durant, OK
- Parts Used:
- WB15K5076
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The door handle on the over was broken.
I removed the oven door from the range. Removed the broken handle and replaced the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Medina, OH
- Parts Used:
- WB30T10099
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
large burner on the dual element not working
The part arrived much sooner than I anticipated. The job was a little harder and took a little longer for me because I'm not good at repairing things. I usually have to call someone. However, I followed the step by step instructions that were provided both on the website and with the mailed item and had no problems. The instructions were clear and easy to follow. The tools needed were very basic - all of which I had on hand. If I could do it - anyone can.
Was this instruction helpful to you?
Thank you for voting!