JCKP17WP-4 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- joseph from san jose, CA
- Parts Used:
- WB36X192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Corinth, MS
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake burned out, checked open with an ohm meter
removed two screws holding the element in place, pulled old element out enough to remove wires that are attached with flag terminals. Installation was in reverse. Turned the oven on and cooked some biscuits. The element that I received from PartSelect was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Centreville, VA
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Short circuited/burned out upper bake element
This is a simple repair of the PS249249 UPPER BAKE ELEMENT requiring only a 1/4 in nut driver or socket wrench.
1. unplug the old element after removing the two screws holding the element in place.
2. Insert the new element in the electrical receptacle and reinsert the screws to secure the new element.
Make sure not to remove any insulation.
1. unplug the old element after removing the two screws holding the element in place.
2. Insert the new element in the electrical receptacle and reinsert the screws to secure the new element.
Make sure not to remove any insulation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Glassboro, NJ
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element feet broke off and element was laying against botom of oven.
Turned off the power at the panel and then simply removed the two hext screws and unplugged the old element. Plugged in the new element and used a nut driver to relpace the two screws.
Was this instruction helpful to you?
Thank you for voting!
Oven elements were not heating properly.
I had to remove two screws that held these elements in place from back of oven; pull the elements out about three inches to disconnect two wires; connected wires to new elements and
replaced two screws.
A very easy job to perform thanks to right parts from PartSelect.
replaced two screws.
A very easy job to perform thanks to right parts from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from fort scott, KS
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Upper over broil unit burned out
This part is a plug-in unit - two screws off; unplug the old unit; plug in the new unit; two screws on. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CASPER, WY
- Parts Used:
- WB21X5301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad sensor
By myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert from Clarkston, MI
- Parts Used:
- WB44K5009
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Broiler element blew out.
- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Pierson, MI
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bake element burned out
My husband (a retired tool & die maker) easily removed the old bake element after first turning off the circuit. He cleaned up the burned salt that we had used to try to put the "fire" out but finally just shut down the circuit. Then just as easily istalled the new element. Thanks to your quick service, we were only without the use of the oven for a day and a half!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from Tucson, AZ
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Just follow the enclosed instructions
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MARIETTA, GA
- Parts Used:
- WB44K5013
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
New element had blade connectors (male).
Drilled small holes in blades to accept existing machine screws from oven wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from Roswell, GA
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Lower Oven Bake Element Burned Out
I should note that my first order to PartsSelect.com
was made on-line and that I selected the wrong part by comparing the burned-out element to the web site picture. When I received that part, I phoned and quickly corrected my mistake, ordered the correct part and obtained return instructions.
With the correct part in hand, I removed the two screws holding the element in place, pulled the element out a short distance to disconnect the two wires and removed the burned-out element. Reversing this procedure I installed the new bake element and completed the job by checking out the oven heating. The hardest part of all this was reaching over the oven door and stretching to unscrew and screw the necessary screws.
was made on-line and that I selected the wrong part by comparing the burned-out element to the web site picture. When I received that part, I phoned and quickly corrected my mistake, ordered the correct part and obtained return instructions.
With the correct part in hand, I removed the two screws holding the element in place, pulled the element out a short distance to disconnect the two wires and removed the burned-out element. Reversing this procedure I installed the new bake element and completed the job by checking out the oven heating. The hardest part of all this was reaching over the oven door and stretching to unscrew and screw the necessary screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harden from Lynchburg, VA
- Parts Used:
- WB44K5009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Element burned out.
I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Charlotte, NC
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
broken element
turn of electric oven, removed screws and took out old element and put in new element and replaced screws. done simple and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tucson, AZ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Probe Sensor
Replaced it
Was this instruction helpful to you?
Thank you for voting!