JCKP14WS-1 General Electric Range - Instructions

.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks

Turned off power. Removed two screws. Took out old element. Used pliers to remove connectors. Installed new element. Set screws. Turned on power. Works.

Ordering and shipment of the part were quick and easy. The price was excellent too. It was the easiest repair we ever had to do to an appliance. After removing the screws that held the element in place and disconnected the part, my husband immediately connected the new part. It took less than 15 minutes.

First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the heating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.

Repair was very easy-make sure you shut the electricity off at the breaker box-having the oven control off does not kill the electricty to the element . Removed the screws, pull out the element, disconnected two wires, re-attach to the new element, install the screws.

removed and replaced

Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bottom and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.

Make sure the oven is turned off. Simply remove the metal cover over the convection fan. Remove the two (2) oven element screws holding it to the oven wall. Disconnect the two wire leads. Connect the new element to the leads and reverse process to attach the new element to oven back wall and install the convection fan cover.

took the old ones out and put the new ones in their slots. No issues

Bake element was glowing. . . Then by the morning, a "cancer-like" thingy traveled the length of it!after kicking off the breaker, I brought the broil down to the bake>. It worked (not recomended>. . But it worked for me). Came the new element, in 2 days. . . And all is back (the broil slots didn't line up so it was a redneck install at best til I got it back to normal). They should add the owner's faces to mt rushmore! Bless you all!

Used nut driver, removed 2 screws and removed old element. Reversed procedure for installion of new part. Can't believe ordered part one day & recieved it next day. Fantastic service. Will definitely call company again.

Installation was really easy. Remove the old bake element, plug the new one in, took at most 10 minutes.

This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!

Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.

ordered part came in noticed i had to make ajustments to new heating element took socket set and unscrewed four screws put a retainer on the wires that came out of the wall to make sure they didn't go back into the wall and would be unretrieveable. installed new screws and cover plate and turned on the oven all done works perfectly.