JCBS28DN1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from Crumpler, NC
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven temp wouldn't regulate.
Followed the directions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from SAN JOSE, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks very old and writing on knobs worn ff
Very was ti replace racks and knobs. Very fast mail service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from GAYLORD, MI
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
front lift burner not working and surface light on with everything off
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from BOULDER, WY
- Parts Used:
- WB02K10158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drawer support broke
Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plastic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Olympia, WA
- Parts Used:
- WB31T10015, WB31T10014, WB03T10167
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken element
Removed the old element and burner bowls and replaced them with the new ones! No screws, no tools needed. PartSelect's prices are cheaper than any other place on the Internet and they shipped me genuine replacement parts, not some 3rd party no-name brand. Also, shipping took less than 2 days! I am thoroughly impressed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from SEATTLE, WA
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken gasket
Popped off old gasket and some retaining clips stuck but were easily removable. New gasket pops right in, super easy. Fits like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Kansas City, MO
- Parts Used:
- WB35X29720
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
A section of the gasket came off the door. It was causing heat to escape.
Found the Model information under the bottom drawer. Googled GE Range and rubber, found this vendor. Amazing, the replacement gasket was exactly as the original. Took the old gasket off with needle nose pliers, there were small metal clamps that had to be pinched together. Once the old gasket was off, the new one practically installed itself. Woman Power!
Baking is MUCH better now!
Baking is MUCH better now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from E WENATCHEE, WA
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
just needed new GE burner bowls
Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helen from PRINCETON, NC
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler unit went out
less then ten minutes, used a electric screw driver and in a snap, finished, I always buy my parts on line at parts select my stove is old but in good condition except parts give out sometimes and I just order part and keep on cooking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from HOPEWELL, VA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Just didn't work no pwr to it
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from EDENTON, NC
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Defective switch
Replaced element control switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from INDIANAPOLIS, IN
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Oven would not get come up to temperature
I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRINDIA from DOVER, TN
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Was burned out
Took back off and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from BENNETTSVILLE, SC
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven could not be turned off once settings were turned on except by unplugging hookup.
Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.
Was this instruction helpful to you?
Thank you for voting!