Models > GRCP3700RM-3 > Instructions

GRCP3700RM-3 General Electric Range - Instructions

Jump to:

All Instructions for the GRCP3700RM-3
16 - 30 of 43
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Herve from Lancaster, PA
Parts Used:
WB36X5712
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Broken Inner Door Glass
We ordered the part from Part Select, got it within a week and replaced the door.
It is a little tricky because one has to dismantle the entire door to do the repair (inside screw to undo).
You'd preferably be 2 to do the repair, although one can manage.
9 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeannene from HUNTINGTON, TX
Parts Used:
WB07K10250
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Part rusted over time...22 years.
Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from FAYETTEVILLE, NY
Parts Used:
WB07K10250
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.
Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from Sarasota, FL
Parts Used:
WB07K10250
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
rusted trim strip
remove screws, re-install screws
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from buford, GA
Parts Used:
WB07K10250
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
bottom trim had rusted out from water build-up
disassembled bottom trim on oven door.cleaned area of excess rust and installed trim piece.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from AKRON, PA
Parts Used:
WB21X5301
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Intermittent heat then no heat on oven element
With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Danial from HILLSBORO, TX
Parts Used:
F26T8-CW-4
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Fluorescent lamp bulb
Unscrew the metal rim and remove the glass window. Remove the old bulb by twesting the bulb towards you. Place the new bulb's pins into the slots and twest away from you. Place the metal rims back in place and screw them down.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Harry from Dills burg, PA
Parts Used:
WB1X500D
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bottom Heating element quit working after 30 years
Removed several screws and removed element. Replaced same. Total ten minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from NORTH HAVEN, CT
Parts Used:
WB7X7187
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
End cap broke on handle
Opened oven door removed screw and broken end cap. Replaced with new end cap and put handle back on
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
joseph from san jose, CA
Parts Used:
WB36X192
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from CASPER, WY
Parts Used:
WB21X5301
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Bad sensor
By myself
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
HAROLD from Tucson, AZ
Parts Used:
WB21X5301
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Just follow the enclosed instructions
Followed the instructions
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
vanessa from runnemede, NJ
Parts Used:
WB07K10250
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
the paint started to chip off.
remove the door, removed about six screws and did a clean up on the glass. the replacement part was screwed back in place. so easy
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Sandstone, MN
Parts Used:
WB21X5301
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda from Lake Panasoffkee, FL
Parts Used:
WB7X7189
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven Door Handle End Caps.
I purchased my stove second hand. It was a mess but I saw a gem under all that dirt and grime. It took me a week and it looked brand new. The end caps on the oven door handle were discolored and cracked. They made the stove look old. It was an easy repair and my stove looks brand new. I will order an extra set just in case as these parts are getting harder and harder to find. I am so pleased with the original parts. They were here with in days and well before promised delivery date.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GRCP3700RM-3
16 - 30 of 43