CSSW2780S-1 General Electric Range - Instructions

Turned off power to oven. Removed two screws that hold the element in place. I then pulled out the element far enough to get to the wires so I could disconnect them. I connected the new element and screwed it back in. 10 mins tops!!!

.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks

I shut off the power at the circuit breaker. I loosened the screws securing the baking element to the back wall. I then pulled out the baking element toward me and found the wire leads bolted using self-tapping screws to the original element. Since the holes on the mounting tabs did not take the old screws, I had to drill out the holes on the tabs of the replacement element. After securely bolting the leads to either terminal on the element, I had to drill two holes on the back wall for the mounting plate of the new element. Then I used the cordless drill with the Philips bit to drive in stainless steel self-tapping screws (not zip screws) to secure the element to the back wall. I turned on the power at the circuit breaker and reset the clock (mechanical).

Needed to drill two new holes for fastening the element to the oven wall. Change in design. Enlarged the holes in the spade connections since I was unable to find smaller bolts than 4-40.
I would suggest to make the holes in the spade connections larger.
The change out was not a problem.

Ordering and shipment of the part were quick and easy. The price was excellent too. It was the easiest repair we ever had to do to an appliance. After removing the screws that held the element in place and disconnected the part, my husband immediately connected the new part. It took less than 15 minutes.

It was easy except that I had to make just a small modification to the electrical connection (holes were to small). . . . Other than that, its was a breeze to install.

I had to struggle to get the pliers to grab hold of the screw because they were so tight. I was worried about "stripping the screws" but finally they loosened and I got them both out. My friend was holding the flashlight, so that helped. I was not real sure what to do next but the wires popped off the element so it was clear that all I had to do was pop the new one on. Easy. I had the most trouble trying to get the screws out. I saved myself $$$. Thanks for your help in sending the correct part!

Repair was very easy-make sure you shut the electricity off at the breaker box-having the oven control off does not kill the electricty to the element . Removed the screws, pull out the element, disconnected two wires, re-attach to the new element, install the screws.

First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the heating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.

removed and replaced

ordered part came in noticed i had to make ajustments to new heating element took socket set and unscrewed four screws put a retainer on the wires that came out of the wall to make sure they didn't go back into the wall and would be unretrieveable. installed new screws and cover plate and turned on the oven all done works perfectly.

I removed the two screws holding the element in, pulled it out, and unplugged it. Installation was reverse of removal. It's just that simple.

Make sure the oven is turned off. Simply remove the metal cover over the convection fan. Remove the two (2) oven element screws holding it to the oven wall. Disconnect the two wire leads. Connect the new element to the leads and reverse process to attach the new element to oven back wall and install the convection fan cover.

Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.

had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.