GRML3500ZAD-1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harvey from charles city, IA
- Parts Used:
- WB07X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Left oven door bracket broken
You need to remove both ends first you block up under the oven door so it is flat to work on then, you will see inside the door the to sleeves that the long screw goes through is easier to screw back in,you are on the road to finished product. H.l.R
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Rio Rancho, NM
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner bowls had been used and abused for year gone by in this rental.
Replaced them all. Next I want to replace the burners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Yadkinville, NC
- Parts Used:
- WB07X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
handles broken on oven door
removed old handles and slid door apart align new handles and re-installed new handles. One person job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Canyon City, CO
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The burner bowls were encrusted with grease and spills.
I easily took out the old ones and put in the new ones sent by Part Select. As promised they fit perfectly. Now when my wife cooks there is no more smoke and it does not set off the smoke detector.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from SAN ANTONIO, TX
- Parts Used:
- WB07X10034
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Handle on oven door end cap cracked
The repair was easy except what caused it to break .Their was a missing screw on the door itself that was never put on or came off could not find old screw,once it was replaced new part was stronger than before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from New Ulm, MN
- Parts Used:
- WB07X10034
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The original oven handle end caps were cracked
I disassembled parts and panels from the oven door as needed to remove the handle end caps. It was not clear to me what the best disassembly method was, because I used a different method when assessing the problem as when I performed the actual part replacement. The quickest way is to take the top two screws on the inside oven panel loose, but leave them in their retainers. Remove the side trim screws on the plastic upper side pieces. Remove the four sheet metal screws on the bottom of the door, located the far right and left (two on each side). Carefully split the inner and outer oven panels to access the mounting screws for the oven handle. Replace the oven handle and reverse the disassembly process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sandstone, MN
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Lubbock, TX
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
6" and 8" burner bowl replacement
Slide out burner elements. Remove old burner bowls. Insert new burner bowls and reinstall burner elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Coal Creek, CO
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The range kept giving an F2 alarm
When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.
Was this instruction helpful to you?
Thank you for voting!