GRCR3950SM-1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Victor from FAYETTEVILLE, GA
- Parts Used:
- WB30T10099
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Repair was slow, due to replacement part was incorrect. Original part had two spring loaded spacers, & holes for them to sit in. The replacement part did not have holes. I was able to drill two holes to make it work.
Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 screws & turned on circuit breaker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cinnaminson, NJ
- Parts Used:
- WB30T10099
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The center element of the 2-stage electric burner failed.
The cooktop is just set in the counter with no fasteners. I shut off the power and lifted the unit out. Ten small screws held the top to the body. After removal, I took a picture to have a wiring reference. I disconnected five wires with push-on terminals, then removed two Tinnerman nuts with needle-nose pliers. The failed burner was free to remove. There were two mounting ears on the bottom of the burner at positions 12 and 48 as stamped on the bottom. I transferred the mounting ears to the new burner, one screw each. I then positioned the new burner and secured with the two Tinnerman nuts, replaced the five wires, screwed the top back on and slipped the unit into the counter. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CASPER, WY
- Parts Used:
- WB21X5301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad sensor
By myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from Tucson, AZ
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Just follow the enclosed instructions
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from san jose, CA
- Parts Used:
- WB36X192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from South Boston, VA
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
only the inner/smaller part of the dual burner is working
I ordered a new burner assuming As is turns out: nothing wrong with the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Tierra Verde, FL
- Parts Used:
- WB30T10099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
small (inner) burner was not 'burning'
turn off the power at the breaker first
remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)
prop up the stove top on the cardboard box the part came in
pull off the wires one by one and attach to the new burner OR record where each wire goes first
remove the old burner (2 screws) and attach the new burner
screw down the stove top
try the burner - when it does not work flip the power breaker back on and then try again
bask in the joy, admiration and wonder directed your way by various family members
remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)
prop up the stove top on the cardboard box the part came in
pull off the wires one by one and attach to the new burner OR record where each wire goes first
remove the old burner (2 screws) and attach the new burner
screw down the stove top
try the burner - when it does not work flip the power breaker back on and then try again
bask in the joy, admiration and wonder directed your way by various family members
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Lexington Park, MD
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cooktop inner ring did not work
Dear PartSelect:
I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.
I simply opened up the cooktop with a screwdriver and disconnected the wires to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.
Matt Brennan
I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.
I simply opened up the cooktop with a screwdriver and disconnected the wires to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.
Matt Brennan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vanessa from runnemede, NJ
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
the paint started to chip off.
remove the door, removed about six screws and did a clean up on the glass. the replacement part was screwed back in place. so easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Pleasant Valley, MO
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Two stage burner was not working on the outer part of burner.
Locate breaker box and turn off breaker to stove. Removed the two screw in front that hold the top in place. Raised the top and supported it with the box the new burner came in. Removed two screws that held the burner in place and the 5 wires one at a time an installed them on the new burner. Put new burner in place and installed two mounting screws. Reinstalled the two screws in the front to hold the top in place then turned the breaker back on and tested burner. Worked great. Received part in 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tucson, AZ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Probe Sensor
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sandstone, MN
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R from Asheville, NC
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing meat thermistor
plug in thermistor when needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Munt Laurel, NJ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Probe broke
Ordered new probe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from San Diego, CA
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Trim has tendancy to rust on range oven door
Unscrewed bottom screws, replaced trim. No trouble.
Was this instruction helpful to you?
Thank you for voting!