JCBP23DM2WW General Electric Range - Instructions

nothing to it.

Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.

The new drip pans are great. I had purchased generic ones locally that were supposed to be universal. The problem was that they did not fit right and the burner coils did not sit flat. The new drip pans fit well and look great too.

The drip pans arrived and she switched them out with the old ones Easy!

just slipped it in

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.

Pull stove out from the wall unplug it remove the old switches and replaced them withe new one. they work just fine.

After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.

Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 days. excellent service. Thanks

Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.

unplugged burners replaced drip bowls plugged in burners

watched the video on part select - took less time then they said.