17568-1 General Electric Range - Instructions

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

Took off the inside ( this allowed me to clean the glass) panel. Removed the two end parts with a screw driver. Replace the parts and we were good to go.

parts need to be delivered to do repair, its been over a month. customer service is not taking calls. I have paid for parts I did not receive.

I attached the end caps to my existing handle, but had to squeeze the parts together very hard to get them to mesh to the correct distance of the holes. I removed the screws holding outside frame of the oven door. I then opened the door fully, propping it up on my knee and removed the inside end cap screws. Placing the handle in position underneath the propped door, I attached the screws. Lastly I reassembled the door.

Open door lift door off hinges lay door face down on flat surface remove 6 phillip head screws 3 on each side lift housing out of door case remove end knob phillip head screws installed one knob insert bar attch second knob and tighten screws lay housing back into casing attach screws doing one at a time on each side slide door back on to hinges and test operate, you are done!

(Followed the ORIGINAL manufacturer's instructions for assembly we retained when purchasing the appliance.) Replacing the broken handle end involved removal of the LEFT handle end as well as the broken RIGHT end, the center rod handle, and unscrewing the outer door face from the inner door face. Had to find specialty screwdriver for non-standard screw heads. Sigh. It was impossible to replace the door handle, as it requires removing the entire door - It is too heavy for one person to hold in place while the 2nd person tried to blindly replace screws thru a 1/2 inch slit in the outer and inner door pieces. Hiring a handyman is impossible leading up to the holidays, so we decided to just buy a new stove. Something that should be really simple to replace for less than $50 is now a major budget outlay due to a crappy design.

Unscrew the metal rim and remove the glass window. Remove the old bulb by twesting the bulb towards you. Place the new bulb's pins into the slots and twest away from you. Place the metal rims back in place and screw them down.

Took door off of hinge
Removed 6 screws from bottom of door
Removed glass
Removed screws from side of door
Removed door from frame
Replaced the end caps using exisiting screws
Put door back together in reverse order
Pretty easy but simple instructions would have made it a 15 minute job instead of 30

Removed several screws and removed element. Replaced same. Total ten minutes.

popped the new one on!

Unscrewed three screws from each oven door. Unbolted the end pieces and replaced with new ones. Reinstalled oven door screws. Nothing to it.

Step #1: Remove 2 screws at the inside top of the oven door that holds the inner/outer oven door together. Step #2: Remove the screws from the inner door that hold the plastic handle end caps to the door. Tip: Use a file to dress up the tips of the metal handle bar so that it fits easily into the new plastic handle end caps. Step #3: Install the first new plastic handle end cap. Step #4: Slide the metal handle bar into the plastic handle end cap that was just installed on the outer oven door. Step #5: Place the other plastic handle end cap on the metal handle bar. Step #6: Install the second plastic handle end cap on the outer oven door. Step #7: Reassemble the oven door by installing the screws that were removed in step #1.

My son took care of removing the broken parts, opening the door and replacing the new handle ends and then finished! It was easy watching him do the work!!!

I took the old cap off, and replaced it with the new one. I am glad I had the sense to buy this online, If I had gotten a repairman to fix this, it probably would have costs $100.00 instead of the $17.00 it cost me to fix it myself. Thanks.

It took longer to go and buy the star tool then the repair. If you have the tools close it is a ten minute repair....