RGB530DEH3BB General Electric Range - Instructions

new igniter had a plastic wire coupling that did not fit with the soves wires; cut off coupling and connected wires with ceramic wire nuts given, remounted ignitor and fired up the oven.

(I could hold a torch on the igniter to start it, then it would work, but would not initially heat up on its own). Pull up and remove oven door. Remove racks. Remove 2 thumb screws in back of bottom plate and remove plate. Remove 1 screw on cover plate. remove 2 screws on igniter and unplug. Splice wires from new igniter to old plug with ceramic wirenuts (included). (Manufacturer changed plug design). re-install everything. (Sears wanted $80.00 for the part, Appliance Factory wanted $47.00).

Over a duration the oven burner would take time to light, then eventually not ignite at all, so repaired ignitor and alls good. Easy, easy, didn't have to disconnect gas, electric for safety.

I followed the directions that I read online and the job was a breeze. I started by disconnecting the electricity, and sliding the oven out from the wall, then taking the oven floor cover off, then ordered Chinese, received a phone call from my sister( blah,blah,blah), Disconnected the old piece, paid for Chinese Food, ate Chinese, installed new piece, reinstalled oven floor, reconnected the electricity, pushed oven back into place, lit oven, turned it off and then tested it again. All in less than an hour.

Every part of the part replacement was easy with the exception of removing one of the two screws that were holding the igniter to gas bar. No fault of the part to be replaced in any way. One of the screws that hold the igniter to the gas bar stripped when I was attempting to remove it. Had to use a small cut off wheel and my dremel to cut the screw and then was able to remove it by screwing it all the way through the hole it was in. Then tapped the two existing screw holes to 10/32 and attached the igniter with new screws. Everything else was about as easy as you can get.

Old school, so I first thought it had to be a thermostat, but realized it did not have a pilot light, but an igniter. Read a few stories of others who had the same issue. Ordered the part, came in early. By that time I knew what I had to do to replace it. Only issue was the part came with a male connector when the original was female. But part came with a couple of ceramic wire nuts, so I guess that is not uncommon. Cut the connectors off and used the wirenuts. Oven is working well.

I went on line found your web sight selected the igniter kit required for my stove. Your web site made it easy to select the part I needed after reviewing the diagram. It was very easy to install just unplug the old unit and plug in the replacement. I would recommend this site to others.
I saved a few dollars; just think if a tech had to come out?

two 1/4 inch screws took oven tray out....two 1/4 inch screws took out ignitor..the replacement would not plug into the wiring, so I cut the plastic plug off and wire nutted ends together..baked cookies after!!!!

First removed 3 screws at burner front and back then pulled out lower storage drawer to disconnect plastic connector, removed and had to cut plastic connectors to use ceramic wire nuts (supplied with parts box) I had to work from underneath stove as well as in the oven it self, if the main door is easily removable it would have helped a great deal but four hours later

Took out bottom of oven, took apart burner & cover. Replace the igniter, , put back together. BAM

First, I was amazed at how fast I received my order. I ordered the part on a Friday morning and i received it Saturday morning. Standard shipping.
The repair should have been much easier than it was.
I removed the oven door by just pulling up and out. then i removed the door underneath the oven. The i reached underneath and disconnected the igniter. From inside the oven, i removed the bottom panel(2 screws). Then i removed the front screw holding the gas tube. I was able to move the tube enough to get at the two screws holding the igniter. one of the screws came out easily using an adjustable wrench. but the other did not come out straight. i had to use tin snips to cut off the igniter so i could acess the screw easier. replacement was in reverse.

the tips you listed from; edward of Pipersville,Pa and Durwood of Suffield,Ct also Billie J of Western Grove, Ar were very helpful. Thanks to them & to you for posting them they were a time saver

removed the screws holding unit in pkce ,unplugged unit'Then I had to cut plug in off new unit and put old plug on new unit. the new unit only had 1 plug and the stove had a2 plug systtem. The put unit back in by replacing thw screws.

Remove botton pan of the oven to get at the igniter, remove bottom drawer to acess wires ,remove 2- screws from the igniter replace then replace oven bottom and drawer.

removed bottom drawer, disconnected screws holding burner in place. unplug igniter. remove bottom tray from inside oven, remove 1 screw holding burner in place near door, remove whole burner assembly. take 2 screws holding element in place. screw new element to burner and reverse procedure. only tool i used was a 1/4 in nut driver.