JVM6175DK2BB General Electric Range - Instructions

remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.

change fuse still didnt work i saw enougher fuse put the new fuse in there old fuse back and it didnt work . it was easy to do but it didnt fix proplem lihgt bulb didnt change coudnt figure how to find were it went

Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

Unplug appliance, Staring from the rear sides, remove the four side screws. Remove the left and right front screws and finally the front center screw. The bottom panel hinges down toward the rear . Unplug the input wires from the sockets . Unscrew the two retainer screws (one each) and pull the sockets out of the panel. Note that the retainer screws are shouldered. The shoulder fits through the elongated slot in the socket. Screw the bulb into the socket and insert through the mounting hole. Insert and tighten the mounting screws. Note that the sockets may appear to be a bit loose. That's OK because of the shouldered screw. Don't over tighten or you risk stripping the threads of the panel. Plug in the input sockets and install the panel screws in the reverse order of removal. Plug the appliance in and test the bulbs.

Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.

Removed 5 screws from the bottom of the over the range microwave to expose the light sockets. Removed the 1 screw holding the socket, disconnected the wires. Attached the wires to the new socket, Put in the bulb, reattached it with the screw. Repeated on the other light... It took about 20 minutes and now the lights work just like they should :)

Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.

Removed the microwave with the buit in housing from the cabinet. Removed microwave from built in housing. Removed outer cabinet giving access to remove control panel and smart board where switches are located. Removed control panel to get to smartboard. Removed smart board after disconnecting a few wires to allow easy removal. Individually removed and then tested each switch using multimeter. Found seondary Door Switch (bottom of smart board) operation to be intermittent (switch trip button extremely loose and rattle inside this particular switch) Ordered replacement part which came very quickly on standard shipping order. Put new switch on smart board and remounted, reinstalled control panel and reconnected various wire connectors previously disconnected. Then plugged in oven and tested for opertation - didn't work at all! But, after bleeding off capacior charge by removing connectors and discharging capacitor to ground, then reassembling control board and smart board into oven, then trying agian, it has worked perfectly ever since. Do not understand why capacitor disconnect/discharge was required but suspect this reset the control electronics. Easy fix and hope to get another 12 years out of this appliance which is used multiple times every day. Also have two other identical micorwave ovens, one is 20 years old, but these get used relatively infrequently.

Changing 2 lightbulbs is NOT ROCKRT SCIENCE. With a screw-driver, remove the under MW light lens, unscrew the 2 burned out light bulbs, and replace with 2 new quality light bulbs. Test out that both are lite and working as they should, replace the lens and you are done, Until you find out one of the new (made in Chins) light bulbs is burned out after about 6 hours of being lite, call the parts phonr number and order a new replace bulb.

The order was easy and promptly received. I lowered the cover by removing retainer screws underneath. Simply lowered it and removed the broken glass and replaced it. The bulb was broken and the base of it was stuck in the socket. I didn't bother to remove it because the socket was brittle. I disconnected the socket by unplugging the wires, removing the retainer screws,and removing it. I replaced it with the new one. Screwed in the bulb. I replaced the cover and it was done. Ps: I used an Hitachi cordless screwdriver, which greatly helped when doing this alone.

As suggested, I placed a towel over the stove. Only had 3 main screws to remove from bottom of microwave. Dropped the bottom and changed the sockets and light bulbs. After replacing the bottom tray, I put the new glass light lens in. The clips on glass holder bent back like a photo frame-really easy. Turned on the lights and was done.

Followed suggestion by previous poster to remove bottom panel...facilitated process well

lower hood; support hood with spice rack;angle just right; unscrew light socket; remove wiring harness; replace; connect wiring harness;

Using a #2 Phillips screwdriver and removed the screw that retains the lens frame around the broken lens. I also did the same to the opposite side (whose lens was fine but the bulb had been burned out for some time). With my fingers I pryed up the frame clips that secure the lens in place, removed the pieces of the broken lens, and replace the lens with one of the new lenses I had ordered. Although the bulb on this side was still burning, I replaced it with one of the two I ordered anyway. When I removed the bulb that was burned out, the glass separated from the bulb's base. However, I simply put on a set of tight fitting leather gloves and used my ring finger to apply pressure inside the base and it soon began to twist and then came out. This takes a little manual dexterity, but is very doable. If it were too tight, you could take a large "easy-out" tool (like the one to fit a 3/8" - 1/2" hole) and it would remove the broken base in short order. I had also ordered a second lens, but the lens on the burned side was simply dirty, so I cleaned it, put it back in place and saved the new one for a rainy day. By the way, BE ABSOLUTELY CERTAIN THE LIGHTS ARE SWITCHED TO THE "OFF" POSITION BEFORE DOING ANY OF THE ABOVE. Also take care to clean the glass on the bulbs with denatured alcohol and handle them with clean cloth gloves or a tissue so as not to allow any oils to be on the surface when they are switched on. Body oil will immediately create a hot spot which will shorten the life of the bulb by at least 50% if not more.