JGB635DEK2WW General Electric Range - Instructions

I first removed the oven door. I then took out the racks and removed the oven bottom. It slips out easily however, you need to take the door off. The burner cover came next. I used the 3/8 nut driver to remove the four screws. This exposed the burner and electric igniter. Two screws hold the burner tube in place. I recommend removing the burner tube due to the screws holding the ignitor will more than likely need to be cut off. Once the tube is out and you have disconnected the plug for the ignitor you will need to check the voltage at the plug (120 VAC). Place the voltage meter test leads in the oven side of the ignitor plug and set the oven to heat up. If everything is OK the meter should read 120 Volts AC. Turn the oven off and remove the leads. Take the old ignitor off the burner tube and replace it with the new ignitor and plug it back into the oven. Push the plug and wires back into the hole in the burner well and put the burner back in the oven well. Once it is all back in and bolted down try the oven again to verify the ignitor works. Replace the remaining oven parts in reverse order of removal.

replace igniter

e-mailed my problem and reply was igniter our gas valve took a gamble and ordered the igniter. easy fix. two srews and plug in wires.

I removed the two screws that hold the element in place then I had to splice the wires because the connector was not right and used the two wire nuts that came with the unit .

removed lower broiler pan so i could see burner igniter. removed the heat shield in front of the gas valve. (1 screw). started oven. no response from igniter. no gas flow at all. if igniter is bad it will not allow gas to flow. ordered new igniter from parts select for my oven model. got it in a couple of days. it wasnt exactly the same as the original, but was compatible. it came with its own connector, but didnt fit. i had to cut it off and splice in the original connector. i had to remove the burner tube to remove the original igniter because the wire was routed around and behind the tube. it just took a couple of screws to remove it and it pulls right off. this is all accessible on the top of the broiler drawer. installed the two screws on the new igniter and plugged in the connector. started oven and igniter started glowing bright immediatly. oven burner lit off within a few seconds. everything working like new now.

Bake ignitor would not glow. Removed racks and lower pan to access the ignitor. Removed two attaching screws and unplugged electrical connector. Installed new ignitor. Hint: Gas will not flow unless both the bake and broil ignitors are operational. Ignitors are interchangable; you can test ignitors by swapping them.

I went on youtube and found videos for similar problems. Then was shown how to test the part to confirm if it was good or bad. After testing with an amp meter I confirmed that the ignighter was bad. I ordered the part and got it in 3 days. I put in the new ignighter turned on the oven and placed inside the oven a temperature gage, when the timer rang on the stove confirming that the oven was up to temperature, I opened the oven door and the temperature gage read 350 deg. exactly the temperature I had set. So for under 50.00 I fixed the oven, a service call would of been 80.00 plus parts. Thanks for the help. Bob Murphy

Removed lower oven panel and replaced oven igniter.

I followed the directions that I read online and the job was a breeze. I started by disconnecting the electricity, and sliding the oven out from the wall, then taking the oven floor cover off, then ordered Chinese, received a phone call from my sister( blah,blah,blah), Disconnected the old piece, paid for Chinese Food, ate Chinese, installed new piece, reinstalled oven floor, reconnected the electricity, pushed oven back into place, lit oven, turned it off and then tested it again. All in less than an hour.

Every part of the part replacement was easy with the exception of removing one of the two screws that were holding the igniter to gas bar. No fault of the part to be replaced in any way. One of the screws that hold the igniter to the gas bar stripped when I was attempting to remove it. Had to use a small cut off wheel and my dremel to cut the screw and then was able to remove it by screwing it all the way through the hole it was in. Then tapped the two existing screw holes to 10/32 and attached the igniter with new screws. Everything else was about as easy as you can get.

This repair was so easy!! I found the part we needed on line with no problem, then I found Parts Select, saved $20.00(honest!) The part was here in 2 days, I bought beer ,called my brother in law and from the call to the oven working was less than an hour. Didn"t break a nail,

Old school, so I first thought it had to be a thermostat, but realized it did not have a pilot light, but an igniter. Read a few stories of others who had the same issue. Ordered the part, came in early. By that time I knew what I had to do to replace it. Only issue was the part came with a male connector when the original was female. But part came with a couple of ceramic wire nuts, so I guess that is not uncommon. Cut the connectors off and used the wirenuts. Oven is working well.

First removed 3 screws at burner front and back then pulled out lower storage drawer to disconnect plastic connector, removed and had to cut plastic connectors to use ceramic wire nuts (supplied with parts box) I had to work from underneath stove as well as in the oven it self, if the main door is easily removable it would have helped a great deal but four hours later

Although the original oven design called for a round igniter, the most recent replacement, done by a service mechanic, utilized a flat igniter. I compared the appearance of this flat igniter to the igniters offered by PartSelect and found that the GE igniter (not the Roper which cost twice as much) matched exactly. I installed it and that solved the problem (of insufficient igniter heat to turn on the gas).

This is a wall mounted oven. Quickly removed the door off hinges (no tools needed). Removed two mounting philips head screws from old igniter. Pulled on wires from the old igniter from back of oven to expose connectors. Disconnected the old igniter. Because the new igniter had a different type of connector, I had to cut connectors off the oven wires as well as the new igniter and use the provided wire nuts. I stuffed the wires back into the back wall of the oven and repositioned the insulation, secured the new igniter and put the door back on. Job done, oven works fine.