JBS45DF2WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janet from Frederick, MD
- Parts Used:
- WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Existing drip pan was burned & beyond cleaning.
Unplugged the burner unit. Removed the existing drip pan. Installed new drip pan in place & re-plugged the burner unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rock Falls, IL
- Parts Used:
- WB30X46987
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
lower burner quit working.
easy, less then 15 min. but take off door first makes alot easier. and don't forget to unplug, like i did. just a few sparks but no damage thank god.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Bellows Falls, VT
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heating element blew apart
I watched the video on this website and it couldn't have been easier. The only thing I did differently was I took the door off for an easier reach. To take the door off, you open just a little and pull up. It makes it so much easier to get at the screws, and maked the repair a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily from Snoqualmie Pass, WA
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler Element Replacement
There were two small screws at the back of the stove (this was the part that intimidated me. At first glance it doesn't look like it should be removed). But you just have to unscrew them, disconnect the wires behind them (this part can be done by hand), and pull the element out. The new element slides right in! Just make sure the power to the stove is disconnected either by breaker or by unplugging it. I'm not sure if it matters, but I made sure to connect the wires to the same side of the element that they were removed from.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Yelm, WA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element not working
Saw the brief video and as stated took less than five minutes to replace. It took longer to clean up the floor under the oven than to replace heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from morton, WA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burned out
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Alice, TX
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out heating element
took 5 minutes with a nut driver and son. I had previously watch your video and went exactly as the video described and showed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from PARIS, MI
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the bottom element of the oven was broken
attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from San Diego, CA
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Trim has tendancy to rust on range oven door
Unscrewed bottom screws, replaced trim. No trouble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lesley from LaPlace, LA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake Element Broke
followed the instruction from your video an it was a snap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deana from Crockett, TX
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip pans
I removed the burners, took the old drip pans out, put the new ones in and put the burners back in. This was so easy that a caveman could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Woodbridge, VA
- Parts Used:
- WB25T10041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Orange light "Hot Stovetop" lense broke off.
Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Chicopee, MA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bake Element burnt out
watched the video on part select - took less time then they said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Hamilton, VA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Old bake element burned out
Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.
Was this instruction helpful to you?
Thank you for voting!