JMS08BA1WH General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Alpine, NJ
- Parts Used:
- WB44K5009
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
broiler element broken -- rotted
First I removed the two screws that hold the element in place. I then pulled the element out disconnected the two wires. THE PROBLEM IS THAT THERE IS HARDLY ANY WIRE TO WORK WITH. Otherwise I would have been finished in ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- hollis from Clarksville, MD
- Parts Used:
- WB44K5013
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
The broil element broke.
We removed the two very tiny screws that held the plate through which the element was connected to the wiring. It was extremely difficult to do so, because the screws were so tiny. Our socket set did not have such a small attachment, and we had to use an adjustable wrench. Once we accomplished that, we unhooked the old broil element from the wires. At that point, the wires snapped back into the wall. There was almost no slack to pull the wires back out into the oven so that we could hook the new broil element up. It took more than an hour of maneuvering before we were able to get hold of enough of the wires so that we could grab onto each one and hook up the new broil element. One we did that, it was easy to place the broil element back into its brackets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurin from Longboat Key, FL
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Current Part had MELTED from heat and broke off
Took door off of hinge
Removed 6 screws from bottom of door
Removed glass
Removed screws from side of door
Removed door from frame
Replaced the end caps using exisiting screws
Put door back together in reverse order
Pretty easy but simple instructions would have made it a 15 minute job instead of 30
Removed 6 screws from bottom of door
Removed glass
Removed screws from side of door
Removed door from frame
Replaced the end caps using exisiting screws
Put door back together in reverse order
Pretty easy but simple instructions would have made it a 15 minute job instead of 30
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from CLIFTON, VA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lower Oven Door End Knobs Cracked And Split
Open door lift door off hinges lay door face down on flat surface remove 6 phillip head screws 3 on each side lift housing out of door case remove end knob phillip head screws installed one knob insert bar attch second knob and tighten screws lay housing back into casing attach screws doing one at a time on each side slide door back on to hinges and test operate, you are done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from great neck, NY
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
a segment of the broil element took on fire
it was real easy, I just watched my husband do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donnie from SAN ANTONIO, FL
- Parts Used:
- WB15K5068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Oven door handle broke
Removed 2 torx screws from enter oven skin then Removed 4 quarter hex head screws to remove handle and installed in reverse and the people at partselect were nice and the parts came quickly. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HOUSTON, TX
- Parts Used:
- WB17X210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old Terminal Block was arcing.
Cut Wires to old terminal block and wired in new Terminal Block
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from BLUFFTON, SC
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken heating element
remove broken heating element and install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PROVO, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls were badly tarnished . . . shine could not be restored.
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Rowlett, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner worked intermittently
Lined up the prongs and slid it right in, took 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST WARWICK, RI
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
a plug on the element broke off while cleaning and replacing
Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from SAVAGE, MN
- Parts Used:
- WB32K5050
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
the oven seal was dried out and crumbling not safe to use on a gas appliance
From what I was able to find info on I was to take out 5 screws 3 on top and 2 on the bottom then the inner oven box is suppose to pull out a bit to take the old gasket off and put the new onw on the box was so rusty it would not pull out so I was able to get enough of the box out using a large screwdriver the lip of the gasket tucks behind the box. I ended up using a small screwdriver to work the new gasket behind the oven box. The door now needs new springs the tension on them is not strong enough to pull the door shut the way it should there's still room to push the door into new gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Mountain View, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Shorted out the burner... fat gets into the receptors on these old stoves.
The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from poughquag, NY
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnrd -out heating elements
Turned AC off. Removed bracket screws and pulled out ac connections. Removed old element and reilstalled new element and set AC on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Indianapolis, IN
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Heating element broke
First turn circuit breaker off. Remove two retaining screws, disconnect two connectors at the end of the element, toss old element and reverse the procedure
to install.
to install.
Was this instruction helpful to you?
Thank you for voting!