JSP34AW1AA General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- joseph from mastic, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bake element burns out heating up easter dinner
Uplugged the oven and undid the back contact cover, removed the nuts inside the oven and slid out the element. Pushed the new element into place and secured it. Attached the contacts and replaced the cover. Plugged it in and got cookin'.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Merrill, WI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Baking element broke
I took out the two racks from inside the oven. I then took my cordless screw driver and unscrewed the two hex bolts from the back of the oven , where the element goes through the other side. Next I went to the back of the outside of the oven and unscrewed the two hex bolts that hold the gray guard on(It covers the wires). I unplugged the red and the yellow (might have been a white wire since it was dark back there). wires that connect to the element. I went to the front of the stove and took out the bad element. I took the new one and inserted it into the two holes from the old element. Plugged the red and yellow wires back up and replaced the guard. Lastly I screwed the element to the rear of the oven with the two hex bolts I used before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dumfries, VA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven bake element burned out (literally!)
Removed oven door & shelves. Removed the 2 mounting screws & compared parts to verify I ordered the right one, then plugged it right in! Managed to drop & lose one of the screws while re-installing them. Got a stainless sheet metal screw from the hardware store that fits, but will probably order an exact replacement because the size & thread are slightly different. All in all, other than losing the screw, it was a quick, easy task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Carmichael, CA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Burned out element
Turned off circuit breaker, removed the two screws, pulled out the wires, unhooked the connections and hooked up the new element. Put the two screws back in, turned on the power and it worked! So, so easy! I wouldn't have attempted it had it not been for the other stories associated with the part I purchased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from east stroudsburg, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
coil burned out
replace coil 2 clips off 2 clips on........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Barnesville, OH
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake element burnt apart
I removed the 2 screwws inside the oven cavity and pulled the element towards me. I unplugged the wires from the element and plugged in the new one and secured it in place with the 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvard Folding Box Co from Lynn, MA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken bake element
Shut off electrical supply to stove.Remove 2 screws.
Slide element out enough to remove connectors from element.
Position new element.Slide connectors onto new element.
Slide element back into position.Replace 2 screws.Turn on electrical supply.
Slide element out enough to remove connectors from element.
Position new element.Slide connectors onto new element.
Slide element back into position.Replace 2 screws.Turn on electrical supply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Bivalve, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Heating element worn-out
Turned off the breaker to the stove, removed oven racks, used small pair of plyers to remove bolts (2) holding defective element in place. Pulled (2) wires that had a snap connection apart. Old element was not removed. Connected (2) snap wires, pushed them back into the oven wall, used plyers to re-connect the element to oven. Installation DONE!
Turned on breaker and then the oven; we are now baking again.
Turned on breaker and then the oven; we are now baking again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Cincinnati, OH
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A teapot melted on one of two working burners
Pulled the old surface element out and plugged the new one in. Took all of 45 seconds!!!!!
It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!
It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Newnan, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Defective
Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using original screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Murray from Franklin Square, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bake element burned out, lower unit
removed nuts from inside, removed rear panel, pulled old
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from SAlisbury, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven was not heating properly
took out the old element after cutting the circuit breaker, put in the new one, it was that easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Plano, TX
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
botton bake element burned out
Removed to screws holding the bake element in place. pulled out element to get to the 2 electrical connectors. removed connectors from old unit. connected new unit and secured with the screwes. very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from Prosser, WA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
For some time our oven had been working eratically, temperature spikes and drops during baking process. I thought the thermostat was the problem. The last time baking, element sparked and overheated in one spot so we removed the element. It was warped and cracked. We replaced it with the new ele
I removed the two screws with a nut driver, pulled the element out far enough to expose the connection point and disconnected the electrical clips. Upon receipt of the new element I did those things in reverse order and it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Charlotte, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom element cracked/split - open circuit
Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & since I was so tired from all of this 5-minute activity, I rested.
Al S.
Al S.
Was this instruction helpful to you?
Thank you for voting!