JBS03GV6 General Electric Range - Instructions

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

First, used the nutdriver to remove the two screws that hold the element. Then pulled out the element 4 inches. Disconnected the two wires from the old element and discarded it. Connected the wires to the new element and tightened them a bit by squeezing with pliers (not too tight, but just enough so they won't disconnect easily). Pushed the wires back through the insulation and screwed the two nuts back in place, making adjustments so that the element is level.

I had a great experience with part select. The part was easy to find and arrive within two days in perfect conditions. Everything went smoothly with the repair and the element is working very well.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the the two screws that connected the wires and element together. I then tried to connect the new element to the wires, but found that the screw holes were smaller than the original holes in the old element and the original screws wouldn't fit. No problem, I then got a cordless drill and found a drill bit a little bigger than the holes, I held the element connector with pliers and made the screw hole a little bigger, same with the other connector. I screwed the screws into the connectors with a socket wrench and then screwed the element back into the holes in the oven, then turned on the oven and it works as good as new.

Removed the cover plate, pulled the element out, removed the screws holding the wires in place, but then I had to enlarge the screw holes on the new element in order to fit the screws into the new element. Took a while with an awl to enlarge ther two holes. Connected the new element, pushed it back in and replaced the cover plate. Worked great.

just plugged it into the socket

I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.

Just put it right into the receptacle. I want to add...we had gone to our local appliance store and brought home a wrong-size unit. Got online and your website came up. It was easy to find the correct part, ordered it and it arrived 3 days later. I have already recommended your website to 2 of my friends. One very good experience!!!

Remove the front panel, at which time the spring loaded door slammed closed while the paned and handle were in my hand. Fortunately I had a star bit to fit the screw holding the door and panel together.The parts should come with 2 screws since the part has holes for 2. note: the factory installed handle only had 1 screw in each side.

Unplugged the burner unit. Removed the existing drip pan. Installed new drip pan in place & re-plugged the burner unit.

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.

Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.

Simply slide stove away from wall and unplug. Remove the center back plate on the rear of the stove, Open oven slide new element into rear of oven, snap into place. Return to rear of oven. slide wire connectors onto oven element prongs, replace center cover, make sure oven is turned off, plug stove back in and slide back into place. Open oven and turn on. allow element to heat up. Once the element has heated and the new burns off. Turn off the oven and replace the racks, This entire process took maybe 5 minutes.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.