PCB900DP1BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- joseph from san jose, CA
- Parts Used:
- WB36X192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kris from Orlando, FL
- Parts Used:
- WB44T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
My heating element on the bottom of the stove burned out.
I unscrewed the 2 screws that held in the element, pulled it out a little, disconnected the 2 wires, got the new element out of the box, connected the two wires on the new element, put the screws back in and it was done! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Jacksonville, FL
- Parts Used:
- WB44T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heating element broken
After reading about possible losses of the wire leads, I put together a simple solution. First, turned off the breaker, then pulled the grates out for full access.
Using a nutdriver on the hex-head screws holding the backing plate to the oven wall, I removed the screws, then gently lifted and pulled the element and it's attached wire leads out of the insulated rear of the oven.
Attach a plastic clothespin to each lead above the spring clip attaching the lead to the element so the springy wire would not tend to pull back into the difficult-to-access insulated area "behind the wall" because that would be a real pain to get at.
With nothing other than fingers, the spring clips can then be removed from the tabs on the element, the old piece removed, the new element set in place and quickly re-connected. No Problem!
Using a nutdriver on the hex-head screws holding the backing plate to the oven wall, I removed the screws, then gently lifted and pulled the element and it's attached wire leads out of the insulated rear of the oven.
Attach a plastic clothespin to each lead above the spring clip attaching the lead to the element so the springy wire would not tend to pull back into the difficult-to-access insulated area "behind the wall" because that would be a real pain to get at.
With nothing other than fingers, the spring clips can then be removed from the tabs on the element, the old piece removed, the new element set in place and quickly re-connected. No Problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Marion, AR
- Parts Used:
- WB44T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Melted bake element
Pulled out stove. Removed rear panel, and set aside. Removed melted bake element by unscrewing the mounting plate screws, and unplugging both leads from the stove. Replaced in reverese fashion. Easiest electrical replacement I have done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DALE from FREMONT, NE
- Parts Used:
- WB24T10153
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Knob stem broke off.
Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CONCORD, MA
- Parts Used:
- WB30T10133
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heating element burned out
Followed example on YouTube! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johanna from Charlton, MA
- Parts Used:
- WB44T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
While making supper, we realized the bottom heating element wasn't working.
We decided to go "on line" to see if there was any way to fix the stove ourselves and found the Part Select website. After entering the model number for the stove, we were able to find the heating element. We ordered it and received it two days later! We saved money and time. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Show Low, AZ
- Parts Used:
- WB44T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change out baking element that did not last as long as it probably should have.
Removed old baking element by removing two sheet metal screws inside the oven and pulling out the old element. When pulling out the old element, one of the wires was too short and popped back into the back of the oven. I then had to pull out the oven, take the shielding off the back of the appliance, gain some slack in the wire and push it back into the interior of the oven. I connected the new element and was finished with the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corey from Orange Park, FL
- Parts Used:
- WB44T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Bake Element cracked
The repair was easy to fix. I unplugged the stove to be safe, unscrewed the broken element and disconnect. And reconnected the new element and screwed it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from North Eastham, MA
- Parts Used:
- WB44T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
burnt out oven coil
turned off power to stove.
removed old coil, as instructed by internet info.
replace new coil.
il
removed old coil, as instructed by internet info.
replace new coil.
il
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALAN from CHARLOTTE, NC
- Parts Used:
- WB44T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Bake Element Burned Out
Removed back cover of stove. . . Just a few screws. . . Disconnected 2 terminals to bake element. Then removed 2 screws inside the oven. . . Holding the element. Replaced with new element. . . Reattached the two mounting screws inside the oven. . . Attached terminals in back. . . Replaced back cover that covered the terminals and other connections. That was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from estero, FL
- Parts Used:
- WB44T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
My lower heating element broke
My 8 year old son did the repair while I explaned what to do,that was the best part of this stove problem. My burner caught fire when it broke and really scared my children. I looked up the part on Part-Select and ordered it. To my complete surprise it arrived the next day(I did not pay for overnight) My son wanted to learn how to take out the old one and put in the new one so I let him. Thanks for a GREAT learning time with my son and for your super service!! Ed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from hermon, NY
- Parts Used:
- WB44T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake ekement burnt out so oven would not heat
I removed the 2 screws that held the element in place. I then pulled the element out and removed the 2 wires. I was able to connect one wire to the new element, but the second wire drew back though the opening. I then had to pull out the stove and remove the center cover on the back of the stove by removeing the screws, there were five or six. do not forget the one in the center of the bottom. I then connected the second wire and replaced the back cover and slid the stove back in place. I then replaced the 2 screws that held in the element in and was done. Worked good as new and no repair bill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from Oviedo, FL
- Parts Used:
- WB44T10011
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Oven element burned out
2 screws removed holding element in. Wires are very short and after removing from the element one wire went back into the insulation. Had to remove the back from the range to get access to wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Conway, AR
- Parts Used:
- WB44T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven heating element had burned out.
Removed 2 hex head machine screws. Picked up on the element and slid wires through. One wire became unattached. Removed back panel, pushed wire through the oven wall, and replaced the back panel. Wires connected with push on connectors. Pushed attachment assembly back through the oven wall and replaced 2 machine screws. Viola! Working oven.
Was this instruction helpful to you?
Thank you for voting!