PGB920DEF2WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ryan from Gunnison, CO
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
oven/broil wouldn't light
Over a duration the oven burner would take time to light, then eventually not ignite at all, so repaired ignitor and alls good. Easy, easy, didn't have to disconnect gas, electric for safety.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Northlake, IL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Igniter would glow but the oven won't turn on
Just replaced the igniter and it works fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Brandon, VT
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bad oven glow plug
the part fit perfect so 5 min, done, thanks for the right part the frist time, I will be back
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from Dover, OH
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Igniter was "cooked"
Unhooked old one, installed new one. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from Carroll, NH
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
wouldnt light
removed oven door & broiler draw took out bottom panel in oven removed part from burner tube reinstalled everything piece of cake works great now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Platteville, CO
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not start when cold.
(I could hold a torch on the igniter to start it, then it would work, but would not initially heat up on its own). Pull up and remove oven door. Remove racks. Remove 2 thumb screws in back of bottom plate and remove plate. Remove 1 screw on cover plate. remove 2 screws on igniter and unplug. Splice wires from new igniter to old plug with ceramic wirenuts (included). (Manufacturer changed plug design). re-install everything. (Sears wanted $80.00 for the part, Appliance Factory wanted $47.00).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Stillwater, MN
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
igniter went out on our gas oven. (no oven heat or flame)
It was quite easy. Uplug the ingnitor and remove two screws from bracket holding it in place along side gas pipe. Plug in new ignitor and and reinstall two screws thru bracket to secure ignitor against gas pipe. Thats it!! Oh, you must remove floor of oven (two Screws,back wall)and remove broiler and door/tray by pulling all the way out to access the ignitor and gas pipe assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Scotch Plains, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Replace the Oven Igniter Component
The job was made very simple primarily due to the repair video that was available on your site when I ordered the part that I was looking for. The job can be done in less than 15 min, but it took me a little bit longer because of some rusted screws that didn’t want to come out so easily. I also decided to take of the front door (not mentioned in the video) just to make it a bit easier to reach the igniter component. The door comes off very easy by opening the door about 6 inches and pulling up and off of the door hinges. Again for a novice like me the video was a life saver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nina from Fairbanks, AK
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
igniter wouldnt glow or allow gas to flow
It was so easy ! take out 2 screws , unplug old igniter, plug in new igniter, replace screws and turn on the heat!! Thanksgiving Dinner is back to my house with the whole Family!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Lawrence, KS
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven igniter would no longer heat the oven.
Repair was very simple. It was a five minute job including time taken to remove old part with a screwdriver and then it was a matter of plugging in the new part ant attaching it to the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Baraga, MI
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Part had burned out
Well first off ordered the part on Monday was here by Tuesday before I went to work. Was able to replace the part the next day and had pizza for lunch for me and the little woman.
Just also want to say Thank You.
Just also want to say Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Feroz from Miramar, FL
- Parts Used:
- WB13K21
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven will not light
Uninstalled the igniter and reinstalled the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Orland, ME
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven igniter
Remove botton pan of the oven to get at the igniter, remove bottom drawer to acess wires ,remove 2- screws from the igniter replace then replace oven bottom and drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pacifica, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
wife complained that oven was not maintaing proper temp
Researched problem came to conclusion that igniter was not staying hot (seemed to intermittently go on and off ). One connector and two screws problem solved and the cherry pies are back in my oven and ready for dessert! : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Devin from Colorado Springs, CO
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
no ignition in stove
replaced the glow bar ignitor
Was this instruction helpful to you?
Thank you for voting!