JB250DF6WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carolyn from Garden City, ID
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed New Burner Bowls
Removed the old burner bowls, replacing them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from JACKSONVILLE, FL
- Parts Used:
- WB04T10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced oven door gasket
Remove old stained gasket and replaced with new. Only $57.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from WEBSTER, TX
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from JACKSON, MO
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
control switch had stopped working, burner wouldn't work properly
took out a couple of screws and replaced with new switch, plugged in switch wires. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Portland, TN
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element blew hole in self then no power to burner.
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SAINT PAUL, MN
- Parts Used:
- WB02X38986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing handle spacer
This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergio from NAPLES, FL
- Parts Used:
- WB62T10614
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Fader/burned paint
Remove heating coils. Unscrew bolt on coil connector. Once that's done the lift to top tilt to one side and it gets light out. The only tools you need or to undo the bolt holding the coil connector that's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LONGS, SC
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven door gasket needed replaced
Ordered the part, it arrived and 5 minutes later it a complete installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent J Paola, from GREENWEL SPGS, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bad Line fault displayed on range clock
1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dock from Aurora, CO
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The storage drawer came without supports.
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from TICKFAW, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Oven board went out
One wire at at time then used my razor blade to get front off stuck right back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from COHOES, NY
- Parts Used:
- WB27X45466
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Bake button stopped registering
This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HOUSTON, TX
- Parts Used:
- WB17X210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old Terminal Block was arcing.
Cut Wires to old terminal block and wired in new Terminal Block
Was this instruction helpful to you?
Thank you for voting!