JGB650SEF1SS General Electric Range - Instructions

I followed the directions that I read online and the job was a breeze. I started by disconnecting the electricity, and sliding the oven out from the wall, then taking the oven floor cover off, then ordered Chinese, received a phone call from my sister( blah,blah,blah), Disconnected the old piece, paid for Chinese Food, ate Chinese, installed new piece, reinstalled oven floor, reconnected the electricity, pushed oven back into place, lit oven, turned it off and then tested it again. All in less than an hour.

Every part of the part replacement was easy with the exception of removing one of the two screws that were holding the igniter to gas bar. No fault of the part to be replaced in any way. One of the screws that hold the igniter to the gas bar stripped when I was attempting to remove it. Had to use a small cut off wheel and my dremel to cut the screw and then was able to remove it by screwing it all the way through the hole it was in. Then tapped the two existing screw holes to 10/32 and attached the igniter with new screws. Everything else was about as easy as you can get.

Old school, so I first thought it had to be a thermostat, but realized it did not have a pilot light, but an igniter. Read a few stories of others who had the same issue. Ordered the part, came in early. By that time I knew what I had to do to replace it. Only issue was the part came with a male connector when the original was female. But part came with a couple of ceramic wire nuts, so I guess that is not uncommon. Cut the connectors off and used the wirenuts. Oven is working well.

This is a wall mounted oven. Quickly removed the door off hinges (no tools needed). Removed two mounting philips head screws from old igniter. Pulled on wires from the old igniter from back of oven to expose connectors. Disconnected the old igniter. Because the new igniter had a different type of connector, I had to cut connectors off the oven wires as well as the new igniter and use the provided wire nuts. I stuffed the wires back into the back wall of the oven and repositioned the insulation, secured the new igniter and put the door back on. Job done, oven works fine.

Replaced the igniter. Quite simple.

Needed to replace the part in oven which lights the gas. My husband is more of a supervisor rather than a fix it yourself kind of guy. But he did it and it was hilarious watching him squeeze in a place meant for a smaller person with tiny hands, while holding the flashlight in his mouth. But the oven is fixed and works like brand new. Thank you

igniter was not glowing bright...removed old one and installed new one all within 30 mins.Part was exactly as description and picture really helped. Turkey for Thanksgiving will be served cooked by my oven.Thanks.. Daniel

Remove the warming drawer to get to the electrical connection, Remove two nuts from igniter, replace igniter fasten the nuts and connect electrical. Oven works fine. BEST PART OF THIS......SAVED $250.

Removed oven door and warming tray. Then removed two screws holding the igniter in place. Disconnect the plug visible below the oven after warming tray removal. Installed new igniter in reverse order.

(I could hold a torch on the igniter to start it, then it would work, but would not initially heat up on its own). Pull up and remove oven door. Remove racks. Remove 2 thumb screws in back of bottom plate and remove plate. Remove 1 screw on cover plate. remove 2 screws on igniter and unplug. Splice wires from new igniter to old plug with ceramic wirenuts (included). (Manufacturer changed plug design). re-install everything. (Sears wanted $80.00 for the part, Appliance Factory wanted $47.00).

It was quite easy. Uplug the ingnitor and remove two screws from bracket holding it in place along side gas pipe. Plug in new ignitor and and reinstall two screws thru bracket to secure ignitor against gas pipe. Thats it!! Oh, you must remove floor of oven (two Screws,back wall)and remove broiler and door/tray by pulling all the way out to access the ignitor and gas pipe assembly.

removed oven door & broiler draw took out bottom panel in oven removed part from burner tube reinstalled everything piece of cake works great now

I unplugged the power then removed the shield from in front of the valve location. I removed the wire shield and pulled the wire connector into the burner area. I unplugged the wire then removed the burner frame pulling it out, I removed and re-installed the igniter kit. I also had to cut the connector from the from the old igniter (about 3" up)then remove the connector from the new (cutting flush to that connector) and switched out the connectors using the porcelane wire ties provided with the new unit. I then re-installed the burner frame making certain that the wires were in the proper location. I plugged the connectors together ensuring proper locking, pushed the wires back into the hole, replaced the wire shield and then the valve cover shield. Restored power the igniter lit brightly and approximately 4-5 seconds later the oven burner lit. I checked connector because another person on the site stated that it may be the wrong one and that the wire connectors would be sent in case that were so.

Took out bottom of oven, took apart burner & cover. Replace the igniter, , put back together. BAM

two 1/4 inch screws took oven tray out....two 1/4 inch screws took out ignitor..the replacement would not plug into the wiring, so I cut the plastic plug off and wire nutted ends together..baked cookies after!!!!