JGB860SEJ1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Trilby from SAINT LOUIS, MO
- Parts Used:
- WB03X24818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The knob on the stove simply came off, couldn't get it back on no matter which way i tried.
It was very simple, I just simply took the new knob and inserted it into place without any problems, took no more than about ten seconds, works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AMON from MARYSVILLE, CA
- Parts Used:
- WB49K10029
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Wrong parts
Your diagram on your website says lower oven is incorrect everything on there is upper oven I ordered the wrong part because your diagrams are all wrong OK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from ST AUGUSTINE, FL
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap replacement
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!
Otherwise everything was great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSE' from WILBRAHAM, MA
- Parts Used:
- WB27X32810
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Had to remove the back guard from the end support to get to the buttom screws!
Had to remove the back guard from the end support. Removed the cover back upper, removed Dorian Gray overlay and control, installed the new one and reinstall all parts working backwards. If it was not that I had to remove the whole panel (back guard from the end support) It would have taken about 15 minutes to accomplish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from PALM COAST, FL
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shortage in wiring cause the housing to burn out
Replaced new light housing.
Thanks to you guys for the prompt response
Thanks to you guys for the prompt response
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from PASADENA, TX
- Parts Used:
- WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from WARSAW, MO
- Parts Used:
- WB13X24924
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
top oven igniter
can not due repair as i have ordered the part four times and it was received broken in shipment all four times.once i recieve credits for the broken pieces i will order another.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from ST CLR SHORES, MI
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner cap wasn't working proper.
took burner off installed new one thank you for fast shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Ft. Washington, PA
- Parts Used:
- WB02K10254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..
Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Albuquerque, NM
- Parts Used:
- WB02T10017
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Convection fan came loose from shaft
Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Thornton, CO
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven lights were burning out regularly
Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tien from Lawrence, MA
- Parts Used:
- WB29K10024, WB28K10222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the cap is crack
I order this parts only take me 5 second to install i realy love love this parts i recommen to people to order you are the best
Was this instruction helpful to you?
Thank you for voting!