JGB760SEF2SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bret from South Haven, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Santa Rosa, CA
- Parts Used:
- WB29K10024, WB29K10023, WB29K10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our burner caps had started chipping.
Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Rio Vista, CA
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven light did not work
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from evansville, WI
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
oven wouldn't ignite
Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 year old oven,it was very easy/.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert K from York, PA
- Parts Used:
- WB16K10070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed To Replace Burner
Took longer to open the box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Shreveport, LA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Igniter went bad
1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter R. from Riverside, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ignter would glow but gas valve wouldn't open
I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the igniter is the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mel from LOGAN, UT
- Parts Used:
- WB20K10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
temperture
replace sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janine from Wind Gap, PA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Oakdale, AL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gas oven igniter for a GE Profile XL44
Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitzi from Briarcliff Manor, NY
- Parts Used:
- WB28K10222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gansevoort, NY
- Parts Used:
- WB08T10002
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
wire connection to socket was bad
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CUMMING, GA
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.
First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from SALEM, WV
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The igniter would glow but the gas would not come on.
I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from DEARBORN, MI
- Parts Used:
- WB13X26360
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
One burner would not light from spark. All other burners lite with spark.
First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Was this instruction helpful to you?
Thank you for voting!