JGB750EEF3ES General Electric Range - Instructions

replace sensor

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

After calling a appliance repair person out because I could not find the module, he pulled the range out so he could remove the top, back cover. He used the correct nut-driver to remove the back. The module is attached to the cover and is exposed when you take it off. Just gently pry the module from the cover. When I saw where it was I paid the repair person for his visit and ordered the new module from PartSelect.com. When it arrived I proceeded to install the new module. I had to use pliers to grasp each connector going into the module and use a flat bladed screwdriver between the module and pliers to get each one to release. I took one wire off at a time and inserted each one into the new module, corresponding to the place it came out of the old module. When I had all the wires inserted into the new module I pushed the new module, using a flat bladed screwdriver, back onto the back cover of the stove. Reattached the back cover with the metal screws and pushed the range back into place. All burners are lighting as designed.

I specifically asked if $16 plus would be the sole expense for this item. I was told that it would be plus there would be no cost for return of the rubber feet. Several hours later I was emailed an invoice that the cost would be $26 plus for four rubber grill screw-like items, a vastly over-priced item. I called and learned through the email system that the item had not been shipped. I requested cancellation at 5AM Saturday. Friday night order led to Saturday morning cancellation -- and Monday morning delivery despite my specific request to cancel. I am not satisfied. It seems like I have been hustled.

I JUST EXCHANGED THE BURNER AND BURNER CAP.

I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.

First I removed the broiler from the bottom of the oven, then pulled the oven way from the wall to unplug it. I then removed the two screws that hold the igniter element in place. Ironically, the plug GE manufactures is reversed so i had to strip the plug and go end and reverse the wires to attach them to the oven. I used ceramic wire attachments as plastic would surely have melted. Replaced the screws, replaced the broilers, plugged it in, replaced against the wall and it fired up.

Order parts and installed - no tools needed - completed repairs less than 1 minute

1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!

un-screw temperature sensor, have to move racks and door, then open back cover board to disconnect the sensor.

1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.

Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.

Replaced the flat style oven igniter. First, I watched the video on your web site, and used it as a reference to make the repair. I did remove the oven door tho, as it made it easier to complete the work, the video didn't show the door being removed. The video was very helpful.