JGB850DEF2WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Solomon A from COLLEGE PARK, GA
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AMON from MARYSVILLE, CA
- Parts Used:
- WB49K10029
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Wrong parts
Your diagram on your website says lower oven is incorrect everything on there is upper oven I ordered the wrong part because your diagrams are all wrong OK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from PAINESVILLE, OH
- Parts Used:
- WB20K10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replace temp sensor in gas range
Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from ST AUGUSTINE, FL
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap replacement
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!
Otherwise everything was great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from BARTLETT, IL
- Parts Used:
- WB16K10055, WB16T10046
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SOUTH ELGIN, IL
- Parts Used:
- WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex R from Randoff, NJ
- Parts Used:
- WB23X5340
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temperature sensor went
Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from PALM COAST, FL
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shortage in wiring cause the housing to burn out
Replaced new light housing.
Thanks to you guys for the prompt response
Thanks to you guys for the prompt response
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond J. from EASTPORT, NY
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
flame was inconsistent. too much air.
replaced old with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from PASADENA, TX
- Parts Used:
- WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from TUCSON, AZ
- Parts Used:
- WB20K10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven sensor not working
Very very simple repair!!!!! Works great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from ST CLR SHORES, MI
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner cap wasn't working proper.
took burner off installed new one thank you for fast shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from WESTERVILLE, OH
- Parts Used:
- WB28X20446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Bottom portion of range would not heat up.
Called sears
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Houston, TX
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace medium burner for gas cooktop
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Was this instruction helpful to you?
Thank you for voting!