JGB26WEA1WW General Electric Range - Instructions

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Replaced old with new.

ordered parts, 2 double burners, 3 days later they arrived.opened box.
lift stove top, lift out old burner,placed next to new burner to see if they were the same. THEY WERE. place in new burner, checked to see if burner assembly fit correctly. IT DID.
units purchased were exact replacements. supplied spacer nuts not needed.
easy fix looks new again, thanks.

I ordered the parts on line and they came very quickly through the mail. The burner assembly came with instructions for the installation of a nut. Everything was great - from the order to the delivery to the installation.

slid the old ones out and slid the new ones in. done

Lifted the top and dropped in the new burners. Realized they always should have had the leveling washers provided so I took the burners off, dropped on the leveling washers and dropped the burners back on. This all took about 2 minutes. Really made the range top look a lot nicer.

I moved to an apartment where the past tenants did not take care of the stove. I think this stove is 10+ years old and looks like it was never cleaned in all of its existance! I cleaned everything really well with oven cleaner and lots of scrubbing. The stove looked brand new except the burners! I couldn't take it anymore so I ordered new ones. The burners came in less time than stated. I opened the box, took the burners out, lifted the oven hood and just placed them right where the others were. There are no tools needed it pretty much just gets placed down in the appropriate spot and that's that! No directions or tools needed. My stove looks awesome now!! When you first use the burners, you will probably need to place a match or lighter by the burner to get the fire going. After that, it lights perfectly every time.

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

Very was ti replace racks and knobs. Very fast mail service

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

Removed torx head screws. Removed broken pieces of the end caps. Replaced the handle installed the end cap screws.

On a 18 year old electric GE range: amazing not the exact handle but it does fit perfectly and looks great. If your somewhat handy this is very easy and can be completed in less than a half hour. Save the screws from the old handle, they can be used again.

The parts were shipped quickly and were what I ordered. The one suggestion I would make to the installer would be to drill out the insert holes a bit in the plastic columns in the inside of the bracket. There are two such columns and they are used to provide further strength to the end cap. However, the diameter of the screw is too large for the insert hole because as I installed the first bracket one of these columns broke. After drilling out the insert hole, the screws were still snug and the end cap (and door handle) was quite solid.

replaced lights in refrigirator and freezer