JGB620DEF3BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from douglasville, GA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven not lighting when turned on.
Replaced the ignitor in the broiler. Two screws holding the ignitor in place and two to the cover holding the quick connect plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Auburndale, FL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
temp in oven not constant big swing in temp
removed oven door racks and pan from bottom of oven. removed warming drawer unplugged oven igniter removed 2 hex screws from bracket on igniter. replaced with new one fiched wire down to warming drawer area plugged in. replaced door and warming drawer. works fine now. very ez to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- grady from Brooklyn, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven did not work
Remove the warming drawer to get to the electrical connection, Remove two nuts from igniter, replace igniter fasten the nuts and connect electrical. Oven works fine. BEST PART OF THIS......SAVED $250.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Alger, MI
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not start.
Bake ignitor would not glow. Removed racks and lower pan to access the ignitor. Removed two attaching screws and unplugged electrical connector. Installed new ignitor. Hint: Gas will not flow unless both the bake and broil ignitors are operational. Ignitors are interchangable; you can test ignitors by swapping them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Vancouver, WA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't heat properly
I went on youtube and found videos for similar problems. Then was shown how to test the part to confirm if it was good or bad. After testing with an amp meter I confirmed that the ignighter was bad. I ordered the part and got it in 3 days. I put in the new ignighter turned on the oven and placed inside the oven a temperature gage, when the timer rang on the stove confirming that the oven was up to temperature, I opened the oven door and the temperature gage read 350 deg. exactly the temperature I had set. So for under 50.00 I fixed the oven, a service call would of been 80.00 plus parts. Thanks for the help. Bob Murphy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from Salem, VA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not get hot enough.
Removed lower oven panel and replaced oven igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Plainsboro, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not light
Removed oven door and warming tray. Then removed two screws holding the igniter in place. Disconnect the plug visible below the oven after warming tray removal. Installed new igniter in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephan from Circleville, OH
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Igniter would glow but oven would not light
I unplugged the power then removed the shield from in front of the valve location. I removed the wire shield and pulled the wire connector into the burner area. I unplugged the wire then removed the burner frame pulling it out, I removed and re-installed the igniter kit. I also had to cut the connector from the from the old igniter (about 3" up)then remove the connector from the new (cutting flush to that connector) and switched out the connectors using the porcelane wire ties provided with the new unit. I then re-installed the burner frame making certain that the wires were in the proper location. I plugged the connectors together ensuring proper locking, pushed the wires back into the hole, replaced the wire shield and then the valve cover shield. Restored power the igniter lit brightly and approximately 4-5 seconds later the oven burner lit. I checked connector because another person on the site stated that it may be the wrong one and that the wire connectors would be sent in case that were so.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Millville, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not light.
First I took off the oven door which was a snap. Then I removed the bottom drawer. I removed the i guess you would call it the spill pan which was two screws. removed the guard plate and disconnect the igniter and remove the two screws that was holding it in place. Peace of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from sayville, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The igniter in the over burnt out
My husband replaced it within 15 minutes,was easy. We ordered the part on a Sunday and had it by Tuesday. Very fast.
thank you
thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shell Rock, IA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven wouldn't heat
removed the screws that held element in place, pulled out old igniter and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Palmdale, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
intermittently would heat - extremely random - 2 year
replaced the ignitor and it has worked perfectly the last week - Service repair walked away from the service call stating it was too random - you website state 91% cause, you were correct I wish I had done this 2 years ago
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- yvonne from havre de grace, MD
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not light on its own
Needed to replace the part in oven which lights the gas. My husband is more of a supervisor rather than a fix it yourself kind of guy. But he did it and it was hilarious watching him squeeze in a place meant for a smaller person with tiny hands, while holding the flashlight in his mouth. But the oven is fixed and works like brand new. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from WHITEHOUSE STATION, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven would not heat
igniter was not glowing bright...removed old one and installed new one all within 30 mins.Part was exactly as description and picture really helped. Turkey for Thanksgiving will be served cooked by my oven.Thanks.. Daniel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Northlake, IL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Igniter would glow but the oven won't turn on
Just replaced the igniter and it works fine now
Was this instruction helpful to you?
Thank you for voting!