JGB635DEK1BB General Electric Range - Instructions

This is a wall mounted oven. Quickly removed the door off hinges (no tools needed). Removed two mounting philips head screws from old igniter. Pulled on wires from the old igniter from back of oven to expose connectors. Disconnected the old igniter. Because the new igniter had a different type of connector, I had to cut connectors off the oven wires as well as the new igniter and use the provided wire nuts. I stuffed the wires back into the back wall of the oven and repositioned the insulation, secured the new igniter and put the door back on. Job done, oven works fine.

I went on line found your web sight selected the igniter kit required for my stove. Your web site made it easy to select the part I needed after reviewing the diagram. It was very easy to install just unplug the old unit and plug in the replacement. I would recommend this site to others.
I saved a few dollars; just think if a tech had to come out?

two 1/4 inch screws took oven tray out....two 1/4 inch screws took out ignitor..the replacement would not plug into the wiring, so I cut the plastic plug off and wire nutted ends together..baked cookies after!!!!

Took out bottom of oven, took apart burner & cover. Replace the igniter, , put back together. BAM

The job was made very simple primarily due to the repair video that was available on your site when I ordered the part that I was looking for. The job can be done in less than 15 min, but it took me a little bit longer because of some rusted screws that didn’t want to come out so easily. I also decided to take of the front door (not mentioned in the video) just to make it a bit easier to reach the igniter component. The door comes off very easy by opening the door about 6 inches and pulling up and off of the door hinges. Again for a novice like me the video was a life saver.

new igniter had a plastic wire coupling that did not fit with the soves wires; cut off coupling and connected wires with ceramic wire nuts given, remounted ignitor and fired up the oven.

(I could hold a torch on the igniter to start it, then it would work, but would not initially heat up on its own). Pull up and remove oven door. Remove racks. Remove 2 thumb screws in back of bottom plate and remove plate. Remove 1 screw on cover plate. remove 2 screws on igniter and unplug. Splice wires from new igniter to old plug with ceramic wirenuts (included). (Manufacturer changed plug design). re-install everything. (Sears wanted $80.00 for the part, Appliance Factory wanted $47.00).

Over a duration the oven burner would take time to light, then eventually not ignite at all, so repaired ignitor and alls good. Easy, easy, didn't have to disconnect gas, electric for safety.

removed the screws holding unit in pkce ,unplugged unit'Then I had to cut plug in off new unit and put old plug on new unit. the new unit only had 1 plug and the stove had a2 plug systtem. The put unit back in by replacing thw screws.

Well first off ordered the part on Monday was here by Tuesday before I went to work. Was able to replace the part the next day and had pizza for lunch for me and the little woman.
Just also want to say Thank You.

Uninstalled the igniter and reinstalled the new one.

Repair was very simple. It was a five minute job including time taken to remove old part with a screwdriver and then it was a matter of plugging in the new part ant attaching it to the oven.

It was so easy ! take out 2 screws , unplug old igniter, plug in new igniter, replace screws and turn on the heat!! Thanksgiving Dinner is back to my house with the whole Family!!!

replaced the glow bar ignitor

replaced the igniter by first removing the pan inside the oven, two screws in the rear. Igniter is attached to the burner with two machine screws, nut driver or small wrench is needed. Remove the lower drawer and un-clip plasitc connection located in the rear up high. Pull the wire and clip through into oven. Replace with new inginater, pull wires and clip through the back of oven and tighten screws, plug clip in, replace pan and plug in oven, done.