JGBS65REF1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from DEARBORN, MI
- Parts Used:
- WB13X26360
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
One burner would not light from spark. All other burners lite with spark.
First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BRADENTON, FL
- Parts Used:
- WB21X20262
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burner Valve stopped working
Turned off gas, then lifted up the burner cover and removed the old valve using a screw driver to loosen the clamp. I also had to remove the face plate using a socket set (4 screws). I didn't align the valve using the existing valves as a guide and also didn't get the clamp tight enough. So I re-aligned the valve to match the other valves and also tighten the clamp enough as best I could to prevent gas from leaking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from REDDING, CT
- Parts Used:
- WB35X37973
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Hard to remove screws & no instructions that a heat shield had to be transferred from old to new
One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard B from CLARKSBORO, NJ
- Parts Used:
- WB28K10222
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Large burner cap finish was damaged
Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Akshay from Bridgeton, NJ
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner had uneven flames
Too easy a five year old could do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from CHICAGO, IL
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Existing oven bottom was damaged.
Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from WARROAD, MN
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter
Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karin from ARUNDEL, ME
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gas burner wasn’t burning properly
I ordered the new burner head and replaced it and now it works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrico from DURHAM, NC
- Parts Used:
- WB20K10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
F 3 code came on my panel, the oven wasn’t getting to the right temperature
I remove the old thermostat and realized right away it was burned, the replacement was very easy to clip on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Solomon A from COLLEGE PARK, GA
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SARATOGA SPGS, NY
- Parts Used:
- WB18X31213
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Igniter failed to stop firing after turning burner off
Used video from YouTube. Presenter recommended unplugging appliance before commencing repairs, but I do not recall a recommendation to shut off the gas supply. When replacing the harness you must disconnect the gas supply rail temporarily. Best to shut off the gas supply to the appliance prior to disconnecting. Otherwise, very straight forward repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SAINT LOUIS, MI
- Parts Used:
- WB20K10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven not lighting
Secured the power, Opened the back of the range, and discovered a rodent chewed the wires in half so I striped the ends and wired them back together, the oven works great !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frankie from CHIDESTER, AR
- Parts Used:
- WB27X42812
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not work, also most other control would not work.
Remove the top panel too get excess to the module. Remove module from panel using screw driver. transfer electric wiring from old unit too new one. replace top panel.
Was this instruction helpful to you?
Thank you for voting!