JB620GF2SA General Electric Range - Instructions

Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

After reading all the repair stories I knew that their wasn't any extra wire when the old element is removed. Well, even with that knowlage one of the wires came loose and slipped back in. Fortunately I was able to remove a panel in back and push it back through. I was afraid I would have to take off the whole back but instead there is a panel covering the wire running down the center of the oven. After removing 5 screws with the same nut driver as the one for the coils I had it done in minutes. I had no problem and I am NOT a 'do it yourselfer'. Oh, did I mention I ordered the part on Friday and received it on Saturday standard shipping? Pays to live the next state over from the place shipping it.

I turned the power off at the circuit breaker, pulled the stove out from the wall, and removed the plug. I removed the top back panel, and took the burner switch out by unscrewing the 2 screws in the front of the panel. I used pliers to remove the wires one at a time from the bad switch and put them on the good switch. I replaced the new burner switch on the front panel and also, replaced the back panel. I put the plug back in the socket, pushed the stove against the wall, and turned the power on at the circuit breaker.

First replaced the 8" burner element-still did not work.
second: replaced the TERMINAL BLOCK KIT still did not work.
third : finally replaced switch: very easly-make sure you do not take off any of the wires on the back of the switch-take new switch and replace each wire on the same location than remove the old switch and replaced wired new on with the two screws.

Went to You Tube, found the appropriate segment. "Wa La" the problem was solved. Burner is working the way it is supposed to.

Well I did it all wrong from the get go. I did finally do a search on how to replace it and then it was quite easy. Learn from me, watch video and save yourself tons of hassle.

Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.

After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.

I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)

Replaced control panel after removing original control panel facing with heat gun and Wala

I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from the wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.

I unscrewed and removed the old element from inside the oven, but unfortunately there wasn't enough extra wire to pull through and attach the new element from the front, so I had to move the oven away from the wall, remove the back panel, and connect the new element from the rear. Very self-explanatory.

The new element had some kind of spray or coating on it that caused some smoke for a few minutes, but then it worked fine.

1. Shut off power at breaker.
2. lift and prop up burner panel (top of stove)
3. removed three screws along top edge.
4. remove oven door (lifts off hinges easy)
5. remove 4 screws along upper oven opening
6. remove 2 screws up under front panel and pull out upper panel enough to access back of switches.
7. unplug wires (5) one at a time and plug onto new switch.
8. remove the two screws from front holding switch in place and remove old switch.
9. install the two screws attaching new switcj.
10 replace all screws in reverse order.
11. Re-install door.
12 close breaker
easy job any one with any mechanical no-how can do.

This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.

After removing power from the range, I pulled the unit out for better access to the rear. I carefully pulled all four knobs off the front of the control panel. Next, using a short phillips screwdriver, I removed two screws from the front bottom of the control panel. On the rear of the control panel, there are four screws to loosen, now the whole panel is free to remove toward the front of the unit. The burner switches are held onto the panel with two screws that are located on the front under where the knob had been. The wires are all connected to the switch with crimp type connectors. These are on tight, but can be removed carefully with pliers. Before doing so, I took a picture on my phone to ensure I replaced the wires in the correct order. Everything goes back together in reverse order. This is a good time to clean behind and under the whole stove. The whole process took around 20 minutes.

I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it complete.