JB745SF3SS General Electric Range - Instructions

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

I just watched the video that was on the website. It showed in detail how to replace the heating element. After watching it I was able to remove the cooktop, replace the heating element and put it all back together. The only issue I had was getting the cooktop loose but once I did everything else was easy.

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

Ordered the part, it arrived and 5 minutes later it a complete installation

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

Removed the two sheet metal screws securing the range top after disconnecting the power. Removed the mounting clips to the old range element and installed the new one. It was an easy fix.

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

replaced Plastic Guides

Remove old stained gasket and replaced with new. Only $57.00!

Pulled the range out and unplugged it. Removed the back of the oven covering the control board. (watched a you-tube video of a similar oven to get basics of how to do it). disconnected the wiring connections and transferred them to the new control board as I removed them. Removed the screws (4) holding the brackets that held the control board in place and removed the board. Had to remove the control board covering that identified what the controls were by carefully and slowly pulling it off as to not crack or break it. Pressed it back onto the new control board. Then reversed the process to re-install it. Once it was back in place I replaced the back covering of the range that I had removed. Plugged the range in and tried out the controls to make sure everything worked.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

First I found a u-tube video on how to repair this. I found the model number of my stove and used my phone to take a picture of it. I found the part on part select.com and ordered it. It came within a few days.
Turn off electricity to the stove. There were two screws to loosen and allow me to lift the glass stove top. It did not come off and we made a stick to hold it open. Then we unplugged and removed the old burner paying attention what was plug in where, maybe 4 plug ins. Then we clipped it back in, closed the top, rescrewed the top on. Turned on the electricity. It took 10 minutes to replace. Very easy!

First tried new oven temperature sensor. No change. Ordered new electronic control board, #PS11700839
and new faceplate graphics, #PS8754650.
1. Applied faceplate graphics to control board.
2. Pulled out range, disconnected power and removed
both rear panel screws with 1/4" power nut driver.
3. LEAVING WIRES ATTACHED I removed the six
screws holding the old control board. I then left the
old control board dangling with the wires still
attached.
4. Installed the new control board with the six screws.
5. One by one, I removed a wire from the dangling old
control board to the new control board. Once all
wires were transferred I double-checked my work.
6. Reinstalled both rear panels and plugged in range.
7. Using two accurate oven thermometers I tested
various temperatures and found that the range
oven heated perfectly as per the setting chosen.

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.