JB700DJ1BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Goldsboro, NC
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven drawer open and close incorrectly
First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Morgantown, WV
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Replace Thermostat
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from MILWAUKEE, WI
- Parts Used:
- WB08T10045
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb burn out
Unsrewed the glass cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from HUNTSVILLE, AL
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
When you touched any button on the controls LOC on appeared.
Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from INDIANAPOLIS, IN
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Oven would not get come up to temperature
I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anil from Milpitas, CA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner spontaneously cycled without knob activation
First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Knob Noster, MO
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken rear drawer support
Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SAN TAN VLY, AZ
- Parts Used:
- WB21X22134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not Reaching Temperature above 300 Degrees
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SAINT PAUL, MN
- Parts Used:
- WB02X38986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing handle spacer
This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Portland, TN
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element blew hole in self then no power to burner.
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from RIVERVIEW, FL
- Parts Used:
- WB24X25013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Only one Burner was heating
Disconnect plug from outlet from stove.Remove nob from control switch rem 2 small screws to release switch.Go to the back and proceed to rem back panel with 1/4 nut driver.Pull out switch and replace one lead a time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from WEBSTER, TX
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from Lexington, OH
- Parts Used:
- WB30T10130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Outside portion of Element broken
First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from HAHIRA, GA
- Parts Used:
- WB14X41386
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Latch n handle to seal the oven during the self cleaning oven wore out and once engaged would not release
Remove the old oven latch and replaced it with the new replacement part. It was very easy to remove and replace with just a few nuts removed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ivan from SNELLVILLE, GA
- Parts Used:
- WB24X25013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
when turn on the larger element would not come on, as the switch moves to the different settings it would light but not staying up.
remove the 4 screw from the back of the control panel take the knob from the front and remove the two screws then raise the rear panel cover up. you can pull the switch from there make picture note of where the plug ups are for replacement its cool
Was this instruction helpful to you?
Thank you for voting!