JB740SF2SS General Electric Range - Instructions

Scary when stove burner comes on by itself, was turning breaker off for safety! GE website not helpful at all. PartSelect website enabled diagnosis of problem and then provided easy source for replacement switch. PartSelect has schematics: all I had to do is unscrew the back of control panel, unscrew offending infinite switch, hook up replacement switch same way, put panel back and done. GE service call starts at $80 and then who knows what kinda $$$? Did repair myself: cost just $38. Yay!

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

Replacement was not very difficult but did require some time. I unscrewed the two areas holding the cooktop in place, slightly lifted the unit up then slid it over a bit to remove from the back area. This unit has the burners affixed to the underside of the cooktop using brackets. Instead of working underneath the raised unit I decided to unhook the cabling in the back and fully removed the cooktop. I moved the cooktop to a flat surface and then I was able to easily remove all of the screws holding the brackets to the burners. I moved all the hardware to the new unit and replaced the cooktop. I was able to dissemble the unit myself but it was helpful having an extra set of hands when it was time to put the new unit in place. Tools used were a socket wrench and a screwdriver.

Ordered the part, turned off the circuit breaker, test to see that power is off, take a 5/16” nut driver, and remove the 2 screws under the front of the stove top, then lift the top up and hold it up with an old 2x4 about 24” long. All the connections are plug and play, so I took some needle nose pliers, to pull all 5 wires off of the burner. Then all that’s left to do is remove 3 spring clips. That was easily done by inserting a flat screwdriver into the back of each clip and pry them out. It ended up being a very easy fix. There is Utube videos to show you how to do it.

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary screw, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

After replacing the dual element and still having a problem with the range, I started troubleshooting the switch. Fortunately, our range has 2 dual burners, and the switches are the same, so I was able to move the switch and see the problem follow the switch (also, using a VOM, I could tell there was a short in the switch).
Since I'd already replaced the element, I only had to work on the controls, which are very easy to access.
I carefully documented all the connections (took a couple of pictures as well), and swapping out the switch took almost no time.
Lesson learned - follow the manufacturer's requirement to use only cookware with a flat bottom. This tea kettle only sat flat around the outside edge. That caused both the element and switch to blow. The "hot cooktop" light stayed on constantly, even after the element was replaced.

This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

I just followed the instructions on the link provided with the part

took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..