JM250DF1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joan from ORLANDO, FL
- Parts Used:
- WB30X20478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was damaged so it didn't work
Easy repair, just had to take the damaged burner out and slide the new burner in....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lan from SANTA CLARA, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
It was burned out
I just follow Steve's Installation Vidio. My range works.
Thanks Steve
Thanks Steve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
Rusted burn box
I simply removed drop in range and removed screws holding burn box and installed new box. Total time was approxmately !hr.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Dills burg, PA
- Parts Used:
- WB1X500D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Heating element quit working after 30 years
Removed several screws and removed element. Replaced same. Total ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lucille from HAPPY CAMP, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner was not heating
unplug it and plug the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from MECHANIC FLS, ME
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced the outlet the one of the top burners on top of my stove, it went very well.
I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PROVO, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls were badly tarnished . . . shine could not be restored.
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from RENO, NV
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
burner terminal block was worn out
I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the burner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from GORDONVILLE, TX
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip pans
Replaced drip pans
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evelyn from FRANKLIN, NH
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Two blocks kept shorting out.
After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from UNION SPRINGS, NY
- Parts Used:
- WB31T10011
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip bowls had deteriorated after years of use
Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Garden City, ID
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed New Burner Bowls
Removed the old burner bowls, replacing them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Aberdeen, NJ
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Hanging broiler
Quick and easy, thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Au Gres, MI
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Could not adjust heat on burner.
Followed directions given by previous customers problems which we found on the internet.
Was this instruction helpful to you?
Thank you for voting!