JM250DF1BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stuart from UNION SPRINGS, NY
- Parts Used:
- WB31T10011
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip bowls had deteriorated after years of use
Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William W. from Seattle, WA
- Parts Used:
- WB24T10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Surface element switch failed
Top front sloping sheet metal panel with all controls and plastic end caps has to come off. Need 2 people, one to hold it while other replaces switch. Problem was getting screw holes on bottom ends lined up and cuts from sheet metal edges. Ten minutes to get it apart, 40 to get it back together. New switch works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CASPER, WY
- Parts Used:
- WB21X5301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad sensor
By myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from reston, VA
- Parts Used:
- WB44X48671
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The bake element in the upper oven broke
I counldn't get the nut screw out. It wounldn't turn. Had to call a technican.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Buckeye, AZ
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.
My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen M from Nampa, ID
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner didn't work, using a test light showed only one side was hot.
took the back panel off the range, took the 2 screws holding the switch in place, took the old switch out, marked the wires took the wires off and clipped them onto the new switch, put the new switch into the switch plate, replaced the screws put on the knob, put the panel back on the range. rolled the range back into it's place. turned the buner on to check if it worked. It did so we were done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Greensboro, GA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner not heating.
Isolated to control switch.
Replaced
Replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from valentines, VA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
eye wouldnt come on
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bryan from cocoa, FL
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
burner was inoperative
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammed from San Jose, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
none to occasional power to burner elements
Exactly followed the instructional video and my installation was flawless. Now the burners power up and function like new. The whole repair was smooth and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Fort Oglethorpe, GA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The burner would not work.
I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Norwich, CT
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burner not heating
Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Apache Junction, AZ
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old,burned pans
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sunny from Salt Lake City, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stained drip bowls
unplugged burners replaced drip bowls plugged in burners
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Leon, KS
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burner wouldnt heat
Watched video,and used it as guideline.Biggest problem was removing tape from old wires.
Was this instruction helpful to you?
Thank you for voting!