JMP26G0J3 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Wayne, OK
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Lower heating element burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Calhoun, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Overn would not heat properly.
Turn circuit breaker off.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!
P.S. Shipping was very fast.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!
P.S. Shipping was very fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Owensboro, KY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
bake element in wall oven burned completely thru
First turned power off for oven circuit at the breaker box then removed two screws that hold element in place. Pulled element out, tested for current, then removed two screws holding wires to element. Took old element from oven and inserted new element. Reattached wires with screws provided, and pushed element into opening. Replaced two screws securing element to back wall of oven. Turned the circuit breaker back on then checked to ensure the oven was working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Aurora, CO
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Oven element no longer would heat
1. Turned the electricity off at the fuse box.
2. Took out the two metal screws holding the element to the oven back.
3. Unscrewed the screws holding the element coil, pulled the element out some and disconnected the two wires.
4. Replaced the old element with the new one.
2. Took out the two metal screws holding the element to the oven back.
3. Unscrewed the screws holding the element coil, pulled the element out some and disconnected the two wires.
4. Replaced the old element with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- arthur from annandale, VA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Old burnt out element
Removed the two screws holding the mount and then reattached the two wires to the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RM from Woodinville, WA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element burned out
I got the help for the install from the help desk. It went EXACTLY as described, I'm so impressed. So got the best price and the best help and we're fixed and I'm baking again. Awesome
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Angola, IN
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Baking Element burned out
Took out old element with screw driver and replaced new element with screw driver, very simple.
We were so happy with the customer service, had the new element the very next morning. Thank you.
We were so happy with the customer service, had the new element the very next morning. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Glenmont, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Broken Bake Element in Oven
Unscrewed face plate, unscrewed electric wires hooked to element. Cleaned out oven while I was in there...nice and clean now. Installed new element same way I took it out. Easy as 'pie'..which we'll be baking again now that the oven works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Wauwatosa, AL
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old element burned out
Turn off power to oven. Make sure with tester that the power is indeed off. Disconnected the two fasteners holding the old unit face plate to rear of oven. Pull the unit outward to expose the leads. Disconnected the leads. Reform new element to remove minor bends so it will sit flat on the floor of the oven. With plies holding the leads straight connect new unit to oven leads. Push new unit back into mounting hole. Reconnect new unit face plate to back of oven. Check that unit is level. Turn the power back on. Test the unit. All works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from kersey, PA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven element burned out
removed the element with 2 screws. disconected element with 2 screws. reversed order to install new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Litchfield Park, AZ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element would no longer heat up.
Shopped online for a good price for the heating element. Thw element came very quickly, very good packaging. Removed and replaced the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Andover, MA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element hot spots and deformed
Looked up mfg. and part #,looked at blow up of stove on parts select, identified element. The part came overnite. Shut down power, removed 2 screws with a nut driver, pulled element foreward to reveal 2 screws attaching wires. Replaced in reverse order, turned on power, back in service. 10 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from Oceanside, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Bake element broke apart at 3 places.
Removed the broken one by disconnecting the two screws , yellow and red wires and replacing it with the new part you sent me. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from SMITHTOWN, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven bake element broke
Bottom bake element is fastened to back wall by 2 screws remove those first.
Slowly pull out old bake element notice 2 wires are fasten to old bake element by 2 philips head screws. Remove screws from wires fastened to old bake element
Discard old bake element.
Reverse the order for assembly.
Replacement part is the exact fit and entire replacement took 15 minutes.
EASY REPLACEMENT
Slowly pull out old bake element notice 2 wires are fasten to old bake element by 2 philips head screws. Remove screws from wires fastened to old bake element
Discard old bake element.
Reverse the order for assembly.
Replacement part is the exact fit and entire replacement took 15 minutes.
EASY REPLACEMENT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Fresno, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
Bottom Element was defective
Unscrewed the two screws holding the element to the back oven wall, then I was able to pull the element out. I then unsrewed the two screws holding the two wires to the element. Installation was the reverse. Pretty simple job.
Was this instruction helpful to you?
Thank you for voting!