Models > JBS27G*R33 > Instructions

JBS27G*R33 General Electric Range - Instructions

Jump to:

All Instructions for the JBS27G*R33
106 - 120 of 550
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Thomas from FORT WORTH, TX
Parts Used:
WB31M20, WB31M19
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Dirty stained drip bowls. Impossible to clean.
Simple replacement
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
megrew, from COLORADO SPGS, CO
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Oven heating element failed
Identify oven breaker and turn off power before starting. Opened oven door. Removed oven racks. Use 1/4" socket or nut driver to remove the 2 bolts holding heating element mounting bracket at rear base of oven. Carefully pull element out of installation mount to remove the 2 machine screws that attach electrical wires to the heating element. Reattach wires in same order as original element. Then reinstall new element in reverse order of removal. Took all of maybe 15 minutes! Excellent OEM Parts!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wendy from CHESHIRE, CT
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Element burned out
My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Todd from Mountain View, CA
Parts Used:
WB30M2
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Shorted out the burner... fat gets into the receptors on these old stoves.
The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rob from Las Cruces, NM
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Lower baking element had burned out.
Using a nut driver, I removed the two screws holding the baking element to the firewall of the oven. I then pulled the baking element out exposing the two wires connected to it. I then used the same nutdriver to remove the nuts and detached the old element. I then connected the new element to the wires, pushed the wires inside the firewall and reattached the element to the firewall of the oven.
The time it took was literally a few minutes. Works like a new oven!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marie from Roxboro, NC
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Baking element had burned out and actually cracked in half.
It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven back. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rex from Colton, NY
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven element melted then naturally would not heat.
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I removed the old element from the oven and replaced it with the new element. Then I connected the two wires to the new element and pushed the element into place. Then I replaced the two screws that held the element in place. I then tested the oven and it worked wonderfully.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from Sacramento, CA
Parts Used:
WB44X173
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Oven wouldn't heat
First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very grateful to have the oven operating again and it was a very inexpensive fix.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JAMES from LEBANON, PA
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Something Had Dripped Down On The Baking Element Causing It To Over Heat In One Spot And Short Out.
This was so easy to do. First I took the two screws out of the holding plate. Then the element comes out and I took the two screws attaching the wires to each end of the element out. To replace it just reverse the above and turn it on let it heat for about 10 mins to burn off any residue and you are ready to start baking again. Although not really necessary it is reccommended to unplug or turn of the breaker before you start working on the problem.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nancy from Golden, CO
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
The heating element in the oven failed, after at least 16 years of good service.
First, we turned off power to the range. We removed the screws holding the element to the back wall of the oven and pulled out the element a few inches. We disconnected the 2 wires from the old element, and attached the new element with the 2 provided screws. We pushed the element back into the wall and secured it with the screws. Turned the power back on, turned the stove back on and, voila, the frozen pizza was well on its way to becoming dinner!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mike from Rowlett, TX
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Burner worked intermittently
Lined up the prongs and slid it right in, took 30 seconds.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mr Sal from Eastampton, NJ
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
element wont heat up
4 screws 4 off then 4 on done
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tracy from Paris, IL
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
elemant had burnt into
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then i connect the new element and and replaced the screwes that held it in very simple and I must say Part select was very fast at getting me the correct part the first time , they have earned a spot in my Favorite list
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Suzanne from Burlington, NC
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
The bottom element in my oven quit working.
Pulled out the bottom drawer of the stove and discovered the plug. So the plug was pulled from the wall socket.

Before this I had sprayed the screws with WD-40 and let it sit for 2 days.

Screws came out easily. Pulled out the old element and removed screws. Screwed on new element on both sides. Put in place and put old screws back.

Plugged stove back in. Turned on stove. Element came right on.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karen from Stuart, FL
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Heating Element Was No Longer Working.
Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.

I put new element in, reconnected two leads, replace two hex nuts and was done.

Turn off power to stove at circuit breaker before starting.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JBS27G*R33
106 - 120 of 550