JGS650DEF1BB General Electric Range - Instructions

I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.

I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the igniter is the problem.

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.

Pull the range out from the wall to access the rear of the unit. Turn off power to the range by unplugging from the wall or turning off the breaker.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unplug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.

Remove door and disassemble door to gain access to inner glass by removing 8-10 screws and nut driver screws remove and clean outer doors remove heat shield and heat Insulation. Reinstall careful to not get fingerprints on inside of glass and replace quick release hinges and door. Careful of hinges as they are spring loaded

I JUST EXCHANGED THE BURNER AND BURNER CAP.

First I removed the broiler from the bottom of the oven, then pulled the oven way from the wall to unplug it. I then removed the two screws that hold the igniter element in place. Ironically, the plug GE manufactures is reversed so i had to strip the plug and go end and reverse the wires to attach them to the oven. I used ceramic wire attachments as plastic would surely have melted. Replaced the screws, replaced the broilers, plugged it in, replaced against the wall and it fired up.

Order parts and installed - no tools needed - completed repairs less than 1 minute

I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.

With the model number I wnet on Parts select site and located the part through the problem finder selection,(GREATFEATURE!) (74% the problem is the Flat Style Oven Igniter) (watched the video on installation and compared my unit with the one in the video). The video explained installation completely and made it very simple. The only critic is that the oven door can be removed completely to make it easier to get in the the oven, opening part way and lifting up the oven door will come completely off. Also the broiler pan drawer can be taken completely out if you would need to get in this way for some reason. Final note: I called the local GE dealer Parts dept- they would have had to order the part anyway and it would have cost three times what Parts Select charged me.Save $$$ great! .

When this happens the plunger switch has to be replaced. This is a small plug like piece that has 4 plug in wires.

So you first unplug the range from the wall outlet. Then remove the oven door off the hinges ( see owners manual for removal ) then you take the right side panel off and there you will see the plunger switch. Before removing the old switch make sure you plug the new one in exactly like the old one. I laid the old one next to the new one and plug them in one at a time. Its a little tricky unplugging them . After a few tries I figured it out. You have to use your thumb and finger and press and pull up by where the wire plugs in. Before putting back together you may want to test the new switch. Plug range back in wall outlet push the black piece that sticks out from switch and if the oven light goes out its fixed. Unplug from wall while reassembling side panel and door. I can say this do it yourself saves a lot of money not having a repairman fix it.

1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.

Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!