JD630SF4SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Woodland Park, CO
- Parts Used:
- WB24X26398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Burner switch not controlling temperature properly. Double Burner
First, Locate the breaker in fuse and shut power off.
Remove all stainless control knobs and set to the side.
I used a 15/16 socket to remove black hold down nuts.
After removing, lift control panel off.
Next, remove 2 screws that hold the control in place.
Remove four 5/16" bolts that hold the control panel in place.
Lift panel and orientate new switch. I replaced one wire at a time and reinstalled the control panel. Pull new switch to align and install screws. At this point I turned the power back on and checked the operation. After confirming proper operation I reinstalled the control panel cover and knobs. Worked perfectly.
" Doing it with Dave "
Remove all stainless control knobs and set to the side.
I used a 15/16 socket to remove black hold down nuts.
After removing, lift control panel off.
Next, remove 2 screws that hold the control in place.
Remove four 5/16" bolts that hold the control panel in place.
Lift panel and orientate new switch. I replaced one wire at a time and reinstalled the control panel. Pull new switch to align and install screws. At this point I turned the power back on and checked the operation. After confirming proper operation I reinstalled the control panel cover and knobs. Worked perfectly.
" Doing it with Dave "
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Glencoe, NM
- Parts Used:
- WB23T10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Remove back panel or access sensor, replace sensor and panel
Removed back panel, change out sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from PALM COAST, FL
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shortage in wiring cause the housing to burn out
Replaced new light housing.
Thanks to you guys for the prompt response
Thanks to you guys for the prompt response
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Zachary, LA
- Parts Used:
- WB23T10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake and convection cycles quit working after a10 minutes
Unbolted temperature sensor from back of oven. Disconnect cable connector. Replaced and reconnected new sensor and bolted back in place. Haven’t had to replace bake element yet, but it’s a major job being this GE Profile oven has the bake element hidden. That’s a new one on me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from BELLE ISLE, FL
- Parts Used:
- WB24T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
The control knob on the burner stopped allowing you to adjust temperature and would on turn the burner off when turning counter clockwise
I turned off the breaker, removed the control knobs from all of the burners there are plastic knots on each control knob that needs to be removed (once loosened they can easily be turned by hand). You can then just lift the out piece off. You need to remove 4 knots to release the control panel so you can access the control know. I removed the 2 screws in the old control know, there are 4 wires that need to be pulled to disconnect. I wrote down the order in which the colored wires were connected . I then removed the old part and reversed the process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vilas from HANOVER TWP, PA
- Parts Used:
- WB30T10132
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Back burner was not working.
Took top of stove off, disconnected the heating element, re-installed the new element and now my stove works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnette from Baltimore, MD
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no racks to oven
Easily glide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orion from Vancouver, WA
- Parts Used:
- WB23T10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven temperature was low when reading was correct
First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Acme, WA
- Parts Used:
- WB23T10015
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
oven temp. was not what setting called for
turned oven off, pulled oven out from wall, removed back of oven, unscrewed sensor from oven replaced with new sensor, put back on, turned power to oven on, tried oven at 425, my temp. gage and the oven temp matched. a very easy fix.
Was this instruction helpful to you?
Thank you for voting!