JBS45DF1BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Richmond, TX
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
GE Electric Range rear left burner quit coming on
Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Lagrange, GA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken bake element
Very easy to install save several dollars
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Ft. Washington, PA
- Parts Used:
- WB02K10254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..
Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Broadway, VA
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
slot that heating element fits was worn down and caused burners to be uneven
replaced with new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Lubbock, TX
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
6" and 8" burner bowl replacement
Slide out burner elements. Remove old burner bowls. Insert new burner bowls and reinstall burner elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Chicopee, MA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bake Element burnt out
watched the video on part select - took less time then they said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rock Falls, IL
- Parts Used:
- WB30X46987
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
lower burner quit working.
easy, less then 15 min. but take off door first makes alot easier. and don't forget to unplug, like i did. just a few sparks but no damage thank god.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily from Snoqualmie Pass, WA
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler Element Replacement
There were two small screws at the back of the stove (this was the part that intimidated me. At first glance it doesn't look like it should be removed). But you just have to unscrew them, disconnect the wires behind them (this part can be done by hand), and pull the element out. The new element slides right in! Just make sure the power to the stove is disconnected either by breaker or by unplugging it. I'm not sure if it matters, but I made sure to connect the wires to the same side of the element that they were removed from.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Yelm, WA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element not working
Saw the brief video and as stated took less than five minutes to replace. It took longer to clean up the floor under the oven than to replace heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from morton, WA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burned out
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from PARIS, MI
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the bottom element of the oven was broken
attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from SAHUARITA, AZ
- Parts Used:
- WB32K10036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven door gasket tore
Slid the oven door off of the hinges and laid it on a sheet on the kitchen island counter top. By simply looking at the spring clips on the new door gasket it was obvious how to use pliers to squeeze the clips on the broken gasket to easily remove it. I took the opportunity to clean the oven door before putting the new gasket on. Installing the new gasket was very easy, simply inserted the spring clips into the holes on the door and pushed until I heard the "click". Anyone can do this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Bellows Falls, VT
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heating element blew apart
I watched the video on this website and it couldn't have been easier. The only thing I did differently was I took the door off for an easier reach. To take the door off, you open just a little and pull up. It makes it so much easier to get at the screws, and maked the repair a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Alice, TX
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out heating element
took 5 minutes with a nut driver and son. I had previously watch your video and went exactly as the video described and showed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Monterey, TN
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!