PGS950EEF3ES General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Astrid from MORAGA, CA
- Parts Used:
- WB16K10055, WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
THE OLD BURNER HEAD WAS NOT TURNING ON PROPERLY AND THE GAS CAME OUT UNEVEN.
I JUST EXCHANGED THE BURNER AND BURNER CAP.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Eldersburg, MD
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner on stove not working correctly
Order parts and installed - no tools needed - completed repairs less than 1 minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GILLETTE, WY
- Parts Used:
- WB23X5340
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The oven does not keep adequate temperature.
Pull the range out from the wall to access the rear of the unit. Turn off power to the range by unplugging from the wall or turning off the breaker.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unplug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unplug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MaryAnn from CAMDEN, TN
- Parts Used:
- WB24X20445
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven Light Stays On
When this happens the plunger switch has to be replaced. This is a small plug like piece that has 4 plug in wires.
So you first unplug the range from the wall outlet. Then remove the oven door off the hinges ( see owners manual for removal ) then you take the right side panel off and there you will see the plunger switch. Before removing the old switch make sure you plug the new one in exactly like the old one. I laid the old one next to the new one and plug them in one at a time. Its a little tricky unplugging them . After a few tries I figured it out. You have to use your thumb and finger and press and pull up by where the wire plugs in. Before putting back together you may want to test the new switch. Plug range back in wall outlet push the black piece that sticks out from switch and if the oven light goes out its fixed. Unplug from wall while reassembling side panel and door. I can say this do it yourself saves a lot of money not having a repairman fix it.
So you first unplug the range from the wall outlet. Then remove the oven door off the hinges ( see owners manual for removal ) then you take the right side panel off and there you will see the plunger switch. Before removing the old switch make sure you plug the new one in exactly like the old one. I laid the old one next to the new one and plug them in one at a time. Its a little tricky unplugging them . After a few tries I figured it out. You have to use your thumb and finger and press and pull up by where the wire plugs in. Before putting back together you may want to test the new switch. Plug range back in wall outlet push the black piece that sticks out from switch and if the oven light goes out its fixed. Unplug from wall while reassembling side panel and door. I can say this do it yourself saves a lot of money not having a repairman fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Frederick, MD
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Oven Light Assembly damaged
I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Akshay from Bridgeton, NJ
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner had uneven flames
Too easy a five year old could do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AMON from MARYSVILLE, CA
- Parts Used:
- WB49K10029
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Wrong parts
Your diagram on your website says lower oven is incorrect everything on there is upper oven I ordered the wrong part because your diagrams are all wrong OK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from GATE CITY, VA
- Parts Used:
- WB23X5340
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not get hot
ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Solomon A from COLLEGE PARK, GA
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from ST AUGUSTINE, FL
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap replacement
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!
Otherwise everything was great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from BARTLETT, IL
- Parts Used:
- WB16K10055, WB16T10046
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SOUTH ELGIN, IL
- Parts Used:
- WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex R from Randoff, NJ
- Parts Used:
- WB23X5340
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temperature sensor went
Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from PALM COAST, FL
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shortage in wiring cause the housing to burn out
Replaced new light housing.
Thanks to you guys for the prompt response
Thanks to you guys for the prompt response
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from PASADENA, TX
- Parts Used:
- WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Was this instruction helpful to you?
Thank you for voting!