JGBS04BEM1WH General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from Geneseo, NY
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not turn off even though knob was turned off.
Unplugged stove. Removed the top rear panel to see where the thermostat cable fed into the oven. Left the current cable in place and fed new cable along side the old one. Pulled out the old cable once new one was installed. Attached wires to new thermostat and installed. Turned oven on to test. Everything went great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnette from Baltimore, MD
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no racks to oven
Easily glide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Birgit from Opelousas, LA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were dirty and wore out
Unplugged the old ones. Cleaned the stove top. Plugged in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from harrisburg, PA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Turn Off
I read the instructions from other peoples repairs. One note: unplug stove, and turn gas off, remember where wires go. I didnt have to remove top of stove completly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Redondo Beach, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
My oven bottom got rusty
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Somerset, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph C from Williamsport, IN
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Temperatures were much usually hotter than indicated
First of all I had to find the right part from Partselect, which was very easy, delivery was fantastically fast even tho I didn`t order special delivery. After reading installation suggestions on the website, it was simple, open the top, disconnect the burners, removed the thermo from the inside. The only hard part was threading the sensor through the correct hole. I had to remove a couple of cover plates to see where the hole was. Put it back together, lit the oven and the temps were correct, as shown by an oven thermometer.
Was this instruction helpful to you?
Thank you for voting!