JGB910CEC4CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Holly from Gaithersburg, MD
- Parts Used:
- WB27K10059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Control Board stopped working after a storm
Turned off gas and unplugged unit. Removed back nuts/screws from range. Took pictures of the wiring in place as a reference. Unscrewed old control board. Held new control board next to old board and plugged wiring into new board. Used the pictures as a reference when needed. Screwed the new board back into place and replaced the back panel on the range. Super easy repair and saved so much money in the cost of the part and all of the labor charges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hubbard, OH
- Parts Used:
- WB02K10136
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replace Motor/Latch assembly
You first must remove the burners on the cooktop to gain access. They are secured with 2 Torx screws which are accesiable after removing the burner covers. The igniters wires must also be removed which simply are push on connections. The cooktop must be removed by inserting a scredriver on each corner of the cooktop from the front. They simply push in and the entire top lifts off. Remove 4 screws covering an access panel located in the front of the cooktop to gain access to the motor/latch, which is secured by two screws accessiable from opening the oven door just below the latch. Replace motor/latch and reassemble. Carefull with the wiring as the replacment switch has been changes. The wires on the left switch of the old assembly get connected to right switch on the new assembly, and the right side wires on the old get connected to left side on the new. Reassemble and Viola!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Raleigh, NC
- Parts Used:
- WB16K10070, WB16K10055, WB16T10046, WB34K10019, WB34K10015, WB29X36765, WB29K10005, WB29K10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
worn parts
removed old parts put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Yorba Linda, CA
- Parts Used:
- WB29X36765, WB29K10005, WB29K10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Chipping around edges of Burner Caps
Received the parts very expeditiously(2 days from time of placing the order), and the replacing of the caps was a "no brainer".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glen from felch, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
uneven flame and sputtered, burner was not useable
Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from North Las Vegas, NV
- Parts Used:
- WB16K10070, WB16K10055, WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
carbonized burners
Replaced all four
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUNSOO from NORTHBROOK, IL
- Parts Used:
- WB28K10024
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Cracked the left burner tubes
I opened cook top without disassemble cook top and broke the left front tube.
After I received left front tube and disassemble cook top to install and found right front tube also not good condition.
I ordered right front tube and installed both tube. I recommend order both front tubes to save shipping.
The tubes were easy to install but little bit hard to remove old Electrode for disassemble cook top and to line up cook top and holder orifice screw hole for assemble.
After I received left front tube and disassemble cook top to install and found right front tube also not good condition.
I ordered right front tube and installed both tube. I recommend order both front tubes to save shipping.
The tubes were easy to install but little bit hard to remove old Electrode for disassemble cook top and to line up cook top and holder orifice screw hole for assemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from New Milford, CT
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The front tubing broke.
The parts were easy to locate on the website, reasonably priced, and arrived in two days. The installation was simple and the parts fit exactly as they should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Los Angeles, CA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not ignite.
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this instruction helpful to you?
Thank you for voting!