Models > JGBS24DEM1CC > Instructions

JGBS24DEM1CC General Electric Range - Instructions

Jump to:

All Instructions for the JGBS24DEM1CC
31 - 45 of 75
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
ERNEST from MANCHESTER, NJ
Parts Used:
WB35X37973
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
finish on old oven bottom was damaged
Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mohammad from BARTLETT, IL
Parts Used:
WB16K10055, WB16T10046
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from SOUTH ELGIN, IL
Parts Used:
WB16T10046, WB16K10055
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Laurie from LEVITTOWN, NY
Parts Used:
WB15T10164
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Stove tipped over and handle split in middle
Bought new handle and replaced it. Once we had correct nutdriver no problem.
Only problem ordered white and received off white, but used it anyway.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roscoe G from ROCHESTER, NY
Parts Used:
40A15
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from Oshkosh, WI
Parts Used:
WB15T10164
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Must have metric set of Tork tool.
After getting the metric set at Harbor Freight the removal and install was easy. Having an extra set of hands is helpful.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
NEIL from ROCKY POINT, NY
Parts Used:
WB08T10026
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dana from LEEDS, AL
Parts Used:
WB01K10112
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charlie from NAPLES, FL
Parts Used:
WB35X37973
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven bottom badly marred after 16 years.
Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from ANDOVER, OH
Parts Used:
WB04K10021
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Rubber cracked
Took 5 minutes to repair easy peasy??
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Claudene from ORCUTT, CA
Parts Used:
WB48T10095
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Juanita from GAINESVILLE, GA
Parts Used:
WB16K10070, WB16T10046, WB16K10055
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Louis from LEAGUE CITY, TX
Parts Used:
40A15
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Change bulb
Easy
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Long Beach, NY
Parts Used:
WB13K10014
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set
To Replace Gas And Burner Parts In Section 4
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregory from Dexter, GA
Parts Used:
WB27K10356
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Oven stays in Preheat mode
first i changed out the temperature sensor that was bad did a ohms check on the old sensor an it showed OL on my meter, after installing new sensor then got a F4 code on display pad changed TO9 Control and that fixed the problem.
7 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGBS24DEM1CC
31 - 45 of 75