JBP70BC1CT General Electric Range - Instructions

well first i came here thewn i called got my part the next day by the way paying only regular postage. it took me more time to pull the stove out and find the sockets then to actually put the element in.that took a whole 3 minutes. thanks partselect you guys are the best and i will be back.

Baking element : Pull range away from wall. Disconnect the power. Remove back center panel. Remove range door. Remove range racks. Disconnect push on terminals fron baking element. Remove two hex head screws. Remove baking element. Reassemble in reverse order..........Temperature sensor: with back panel removed, unclip the electrical connector. Remove one hex head screw. Remove temperature sensor. Install in reverse order.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

replaced lights in refrigirator and freezer

To 80 year old (young) brothers worked together. One hooked the wires the other one plug it in. Very simple install.. Neither one knows anything about electricity. Thank you for your service.

First I removed the two screws that held the element in place. I then took the plate off the back of the range disconnected the two wires from the element and removed the old element. I then inserted the new element into the oven screwed the nuts back on and hooked the wires on the new element from the back put the plate back up on the back and screwed the nuts back on. It took around 15 minutes to do it all and this was the first time that I have ever done this. It was so easy.

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

Lots of jiggling until I found the screws to remove. After finally getting the top off the base there was the Instructions on a pamphlet taped to the bottom. The key tho get the top off is to remove the face and remove the proper screws( they are identifiable)unplug the electric plug 2 screws on the back sides and poof it is free!

The only hard thing was contorting my old beat up body and joints long enuff to reconnect the 2 wires and oven heat sensor and put in 6 screws with a 1/4" nut driver. I did remover the oven door and that made it much easier for me.

Unplugged Stove. Removed two screws. Unplugged two wires from heating element. Connected the two wires to new heating element. Replaced screws. That's all. 5 minute repair job.....(45 minutes to find right socket haha)

Ordered new heating element on Friday afternoon (3pm) and received part on Saturday at 1:00pm. Impressive! (standard shipping)

removed the two screws,then pulled element out and removed the wires,took out element that needed replacing, then connected new element . the repair job took no time at all. i was really impressed with how easy it was.

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

I too made the mistake of cleaning the oven with the shelves in place. It doesn't really harm them...but they turn a tarnished brown color...they look dirty. These replacement shelves were a perfect match. Pricing was reasonable, communication was terrific and shipping was super fast. Happy camper here :-)

Very easy to replace. So easy even a man can do it.

I had my husband fix it! Very easy for me.

It didn't take him long. The most difficult part was getting to the screws. He had to practically climb into the oven.

The parts were shipped promptly and the whole process was relatively painless!