JGS905SEK2SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- walter from townshend, VT
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was not getting up to temp
Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Simi Valley, CA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Leaking from front door
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Knoxville, TN
- Parts Used:
- WB13X46909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The spark module would constantly spark
I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Port Orchard, WA
- Parts Used:
- WB16T10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners are supposed to burn with a blue flame. Two burners had yellow flames
New burner Heads repaired the two yellow burning units. I believe heat caused the old heads to become. warped over time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shakopee, MN
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Stove drawer rear guides broken
Installed new guides with a nut driver without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Bethesda, MD
- Parts Used:
- WB04T10050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gasket on door was brittle
I feel like Macho Mom. I called in the repair guy since I was afraid of dealing with the gas. HE repaired one item but could tell I was comfortable fixing things and pointed out that the gasket was brittle and would cause major problems if not replaced. Took longer to order the part than do the repair, don't know what I was afraid of!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judith from boardman, OH
- Parts Used:
- WB16T10037
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
warped burner
reinstalled new one. just a little better than than the warped one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Newark, DE
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Range lower drawer would not stay on track.
Easy to install replacement parts using the screws provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Deer Park, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken drawer support
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Stuart, VA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic slide for storage drawer broken.
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jud from gatesville, TX
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
F2 error code
Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lisle, IL
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven not warming, f2 indicating overheat
Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Watertown, MA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the grate foots came off
put it in but it keeps falling out. they're made narrower than my oven grate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Lansdale, PA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hard to move drawer in and out because the rear drawer supports broke off.
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Salem, OR
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Flashing F2 and erratic temperature readings.
Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.
Was this instruction helpful to you?
Thank you for voting!