JBP21BH2WH General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from BENNETTSVILLE, SC
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven could not be turned off once settings were turned on except by unplugging hookup.
Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Victor, ID
- Parts Used:
- WB02K10144
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Cleaning oven latch engaged while pizza was cooking
In a panicked state, my roommates and I could not turn the cleaning setting off. So, we "Jerry-rigged" the door open to save the house from the awful burning pizza smell and potential fire. We removed the stove top with the nutdriver only held in with three nuts. Removed the insulation promptly after. Disassembled the latch mechanism with the star wrench set. The scariest part of the replacement was looking confused at the new part. To our dismay, the part looked grossly under sized. we thought it would not fit. After placing the part in place of the broken latch we found the replacement fit better than the previous and was a totally painless success. Do-it-yourself, not that complex and an excellent way to save money.
_Jeffrey B.
_Jeffrey B.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from EDENTON, NC
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Defective switch
Replaced element control switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PHOENIX, AZ
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stove overheated with an F2 error
Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- candace from RALEIGH, NC
- Parts Used:
- WB15K10046
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
OLD HANDLE TWO PIECE MODEL FELL APART
REMOVE TWO TORX HEAD SCREWS AT TOP OF INNER DOOR
PANEL. THEN REMOVE TWO ALIGNMENT SLEEVES THAT WERE
HELD WITH SHEET METAL SCREWS AND DISCARD BOTH THE SCREWS (SHEET METAL) AND THE SLEEVES. ALIGN TWO SMALL PINS ON EITHER SIDE OF OUTER DOOR PANEL AND ATTACH WITH THE TORX HEAD SCREWS(MAY WANT TO USE A DRILL IF YOU HAVE THE CORRECT TORX BIT). NEW HANDLE ONE PIECE BETTER DESIGN... WIFE LOVES IT.
PANEL. THEN REMOVE TWO ALIGNMENT SLEEVES THAT WERE
HELD WITH SHEET METAL SCREWS AND DISCARD BOTH THE SCREWS (SHEET METAL) AND THE SLEEVES. ALIGN TWO SMALL PINS ON EITHER SIDE OF OUTER DOOR PANEL AND ATTACH WITH THE TORX HEAD SCREWS(MAY WANT TO USE A DRILL IF YOU HAVE THE CORRECT TORX BIT). NEW HANDLE ONE PIECE BETTER DESIGN... WIFE LOVES IT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from HOPEWELL, VA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Just didn't work no pwr to it
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Morgantown, WV
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Replace Thermostat
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helen from PRINCETON, NC
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler unit went out
less then ten minutes, used a electric screw driver and in a snap, finished, I always buy my parts on line at parts select my stove is old but in good condition except parts give out sometimes and I just order part and keep on cooking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lan from SANTA CLARA, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
It was burned out
I just follow Steve's Installation Vidio. My range works.
Thanks Steve
Thanks Steve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from GORDONVILLE, TX
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip pans
Replaced drip pans
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from PICKENS, SC
- Parts Used:
- WB30X24401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Porcelain melted on burner
Simply shoved the new one into place.. tada done. Woohoo thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from RANCHO MIRAGE, CA
- Parts Used:
- WB02K10061
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken drawer glider
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTONIO from E STROUDSBURG, PA
- Parts Used:
- WB31T10011, WB31T10010, WB30X24401, WB30T10074
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I'm Very Very Happy Was My First Order From This Part's Company ;
100% Pleased I Got & Installed All In A Few Minutes Your Company Is The Best Thank You Very Very Much ; Antonio
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from SAN JOSE, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks very old and writing on knobs worn ff
Very was ti replace racks and knobs. Very fast mail service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from GAYLORD, MI
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
front lift burner not working and surface light on with everything off
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this instruction helpful to you?
Thank you for voting!