JBP80TK1WW General Electric Range - Instructions

Performed repair using a video for reference.

I am a 62 year old woman with NO experience fixing appliances However I didn't have the money for a repairman so I ordered the part and googled "Hiw to change a heating element in a GE range". All the instructions were there and now my oven is working perfectly. I even posted on Facebook for my female friends to encourage them to do repairs themselves. What a GREAT feeling.

Took me a second to remember that YouTube is just as handy a tool as what I've got in my toolbox. The installation of the new glass was as easy as apple pie. Anybody that has ever used a screwdriver could manage that fix and do so single handedly. PartSelect.com came through with an easy-to-navigate website, a very reasonable price range and anything you could ask for to help fix whatever has broken. I quoted a gentleman in my town, a handyman, and he came back with a price tag of over $300 for parts and labor! Even with tax, shipping and the new glass I came in well under $100, and the labor was next to nothing. If i ever have to replace or fix something in my house again, I'll be using them, Without a doubt. Thanks for everything, dudes. Cheers!

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

I pulled out the range from the wall unplugged it from the wall then i opened the oven door and removed the two small screws on the front off the range and lifted the glass top and supported it with a 1/2" X 18inc wooden dowel, then i removed the two burner retaining screws with a small Phillips screw driver and removed the wires from the burner,
then i replaced the burner with the new one and reconnected the wires and placed the burner in to the two retaining clips and then tightened the two screws then i removed the wooden dowel and installed the two screws on the front bottom side on the range then i plugged in the range in and tested the burner then put the range back against the wall.

Simply pulled old gasket from door and pushed new gasket clips into existing holes and tucked in ends at bottom of door.

I went online and ordered the part after reading other people's repair experiences, confident that I could do it because the part was quite pricey. First, be sure you're circuit breaker to your range is off. Next, open the oven door and locate and remove two screws with a socket, that are just under the top surface which will allow you to lift up the glass top which is actually hinged...no need to pull the range out. Securely prop up the glass surface area and the burners are exposed. With a marker, mark where each color wire goes on the burner you are going to remove and also mark where the two holding brackets are. This way you can reference the locations to connect to the new one. Carefully remove the wires and brackets and install new burner with brackets and connections. Close up the top, replace two screws, turn on breaker, and if there were no other faulty components,it'll work great. P.S Be gentle getting the very snug wires off. Good Luck

I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.

In this case I had to pull the range out to disconnect the power and also to remove the plate covering the electrical connectors. This was the only way to reconnect the elements terminals since the wires were too short to do it inside the oven. Undo the 2 screws holding the element in place from inside the oven to remove and install the new one before connecting the terminals from the back. Put back the rear cover and reconnect the power.

Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

I removed the control panel by removing 7 screws and replaced the light indicator and lens.

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. Connected the wires and resecured top to base. Turned on the current and it worked beautifully.