JDP39BW6BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from BARTLETT, TN
- Parts Used:
- WB15K5076
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
door handle and end caps broke
parts need to be delivered to do repair, its been over a month. customer service is not taking calls. I have paid for parts I did not receive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from AKRON, PA
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent heat then no heat on oven element
With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.
One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Houston, TX
- Parts Used:
- WB15T10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
children used it for a chin bar and broke the handle and the piece that holds the handle on
We had to buy washers and screws to hold the handle on.
Then all we did was undo the screws that were on the side of the door. place handle on door screw the new screws and washers that we had to buy and replace the side screws and it was fixed.
The only problem that I found was that the handle kit did not come with screws or some kind of attachment to hold the handle on the door. We had to buy extras at the hardware store for that.
Then all we did was undo the screws that were on the side of the door. place handle on door screw the new screws and washers that we had to buy and replace the side screws and it was fixed.
The only problem that I found was that the handle kit did not come with screws or some kind of attachment to hold the handle on the door. We had to buy extras at the hardware store for that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Clarksville, OH
- Parts Used:
- WB23K5027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner control was erratic. Sometimes it worked, sometimes it didn't.
First pull knob off switch. You may need a small screwdriver to gently start it. I then removed two screws, one in each end of control panel. Then rolled the panel up and out, as it is kind of hinged in the back. Removed two screws from switch front,layed it to the side and installed new switch. Removed wires (there were 5) one at a time with needle nose pliers, and placed on new switch. Replaced panel screws and was finished. Easy fix, quick delivery of part, I have used Partselect in the past and will continue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BEVERLY from PHENIX CITY, AL
- Parts Used:
- WB57T10110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven door glass broke
First, I cleaned all the glass from the stove. then I inserted the replacement glass into the slots and screwed the bolts back into the stove. It took me about 1o minutes to do repair. It waS VERY EASY..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry J from South Haven, MI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven stopped heating and element appeared broken
The customer service rep was brilliant in finding the
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from assumption, IL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
bake element burnt into
repair went fine, real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- allen from MT. AIRY, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
bake element was broken
i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from OAKLAND, MD
- Parts Used:
- WB23K5027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Surface burner switch malfunction allowing the burner to remain on high heat after turning to low heat.
I removed two small screws located on the underside of the control panel. I then rotated the bottom of the control panel up and dislodged the few connections at top back of control panel. The control panel became loose enough to lay forward exposing the inner control switches. The old problem switch wiring was removed one by one and placed in the same spot on the new switch. The old switch was then removed by pulling off the front control knob and then unscrewing two screws holding the old switch in place. Then the new switch was installed exactly as the old switch was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derrick from Ypsilanti, MI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven no longer heated except for Broil element
1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from MILROY, PA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
on off switch smoked and smelled hot
standard procedure, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from madison, WI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Uns rewed and pulled out
At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lynette from Bowling Green, KY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Element burned out.
Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurin from Longboat Key, FL
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Current Part had MELTED from heat and broke off
Took door off of hinge
Removed 6 screws from bottom of door
Removed glass
Removed screws from side of door
Removed door from frame
Replaced the end caps using exisiting screws
Put door back together in reverse order
Pretty easy but simple instructions would have made it a 15 minute job instead of 30
Removed 6 screws from bottom of door
Removed glass
Removed screws from side of door
Removed door from frame
Replaced the end caps using exisiting screws
Put door back together in reverse order
Pretty easy but simple instructions would have made it a 15 minute job instead of 30
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Rockport, ME
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not get to temperature...200 degrees max
Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Was this instruction helpful to you?
Thank you for voting!